GEA VARIVENT C Скачать руководство пользователя страница 54

Страница: 54 / 80

Fig.28

It will not hurt if the disc on the end of the cleaning hose turns.

Re-assembly

Carry out the following steps:

After removing the union nut replace it without using aggressive force. Make
sure that the nozzle is also tight.

Done

10.7.2 Torques for the Clamps and Clamp Connections

Tighten the clamp connection and semi-rings on the valve to the torques
specified in the table.

Torques

[Nm]

[lbft]

Clamps on the
control top

0.7

Clamp connection
cast half rings

6.6

Clamp connection
cast half rings

16.2

Cast clamps

M10

10.7.3 Checking the function

Setting the valve stroke

Carry out the following steps:

Actuate the valve with compressed air.

Check the stroke of the valve in accordance with (Page 54).

The stroke is set.

Strokes Depending on Size

Valve Stroke

Valve size

Valve stroke [mm]

Metric

Maintenance

Installation

430BAL008331EN_4

18.02.2022

Содержание VARIVENT C

















































































Результаты поиска

Содержание VARIVENT C

Отзывы:

Похожие инструкции для VARIVENT C

Бренды по названию

Популярные бренды

GEA VARIVENT C, Руководство пользователя

Результаты поиска

Содержание VARIVENT C

Отзывы:

Похожие инструкции для VARIVENT C

Бренды по названию

Популярные бренды