GEA Futuro Скачать руководство пользователя страница 70

Страница: 70 / 108

Installation

Information on disposing of material after installation is finished

2007-9015-001
03-2014

70 / 108

● If a hose must be installed over a

sharp edge or corner it must be
supported to avoid abrasions.

● The illustration shows how to

properly support the hose.

● Avoid clamping a hose in a bend as

the bend absorbs the energy as the
hose moves under pressure.

● Install the two orange non

conductive hydraulic hoses between
the hydraulic power unit and the
equipment.

● The purpose of theses non

conductive hoses is to electrically
bloc the potential stray voltage
transfer between the hydraulic
power unit and the equipment.

Note!

Some installation may require to use hydraulic hose extensions. In this
case, keep the orange hoses in place and connect extensions
between equipment and orange hoses.

5.9

Connecting the Futuro to the hydraulic power unit

● Using orange hydraulic hoses from the power unit, connect the Futuro

reversing valve.

● Once connected, make sure 2 ball valves under the power unit are opened

to allow oil circulation.

5.10

Information on disposing of material after installation is finished

Handle unused installation material properly and dispose in accordance with
current valid local regulations on waste disposal and utilization.

Содержание Futuro













































































































Результаты поиска

Содержание Futuro

Отзывы:

Похожие инструкции для Futuro

Бренды по названию

Популярные бренды

GEA Futuro, Инструкция по эксплуатации и руководство по установке

Результаты поиска

Содержание Futuro

Отзывы:

Похожие инструкции для Futuro

Бренды по названию

Популярные бренды