manualshive.com logo in svg

GE WDSS4120, Техническое обслуживание руководство, Страница: 35 / 46

Поделиться
Скачать
GE WDSS4120 Скачать руководство пользователя страница 35

To avoid risk of electrical shock, personal injury, or
death, disconnect power to unit before servicing.

Disassembly Procedures

32

WARNING

!

Transmission Assembly

1. Remove outer tub, see Outer Tub” procedure,

steps 1 through 11.

2. Remove screws securing each support leg to outer

tub. Lift "milk-stool" assembly, and brake assembly
off transmission tube.

NOTE: It may be necessary to tap lightly on "milk-stool"

assembly to loosen it from transmission tube.

When installing lower bearing, "milk-stool"

assembly and brake assembly, apply Anti-Seize
Compound (WH60X10005) to area of
transmission tube that will be contacting
bearing.

Do not overtighten screws as this could cause stripping
or damage. Torque screws between 100 to 150 inch-
pounds.

NOTE: When replacing or reinstalling transmission

assembly, it is important that Anti-Seize
Compound (WH60X10005) be applied to area
of the transmission tubes where they will be
contacting upper and lower bearings.

Carefully lower transmission through upper bearing. DO
NOT DROP OR LOWER TRANSMISSION ASSEMBLY
INTO POSITION TOO HARD. This  can cause bearing to
move which will cause vibration, noise, wear or no spin.

Upper Bearing Assembly

1. Remove transmission assembly, see “Disassembly

o f  Transmission Assembly” procedure.

2. Remove screws securing each support leg to

outer tub.

3. Lift complete "milk-stool" assembly (with drive

pulley, brake assembly, lower bearing, and
transmission assembly attached) off outer tub.

NOTE: Do not overtighten screws as this could

cause stripping or damage.

4. Remove screws securing upper bearing and

housing to bottom of outer tub.

NOTE: Replace bearing and housing as an

assembly. When upper bearing assembly is
reinstalled, threads of cap screws must be
secured with a retaining compound.

Friction Ring

1. Remove outer tub, see “Outer Tub” procedure

steps 1 through 11.

2. Remove friction ring and replace with new friction

ring.

3. Reverse procedure to reassemble.

NOTE: When installing module springs, make sure

spring hooks are fully seated in the holes.

Содержание WDSS4120















































Отзывы:

Нет отзывов