GE WDSS4120 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 46

GE WDSS4120 Скачать руководство пользователя страница 27

To avoid risk of electrical shock, personal injury, or
death, disconnect power to unit before servicing.

Disassembly Procedures

24

WARNING

!

7. Apply a small amount of supplied grease to inside

sealing lips of seal.

Apply grease to
inside sealing lips

Transmission
output shaft

Seal

Hub
assembly

NOTE: DO NOT allow any lubricants to come in

contact with outside surface of seal

8. Apply remainder of supplied grease to exposed

surface of washer between transmission output
shaft and seal.

9. Place new drive bell seal onto hub and push into

position using large end of WX05X10001 Seal
Tool.

NOTE: Using a small pocket mirror, check entire

circumference of bottom seal flange to verify
seal is pressed down against shoulder on
hub; there should be no gap!

10.Turn WX05X10001 Seal Tool upside-down and

place the small end over transmission output
shaft and onto the seal.

11. Push down on tool with a quick motion until it

bottoms out and the top of seal is fully seated.

Hub
assembly

293P4
Seal tool

293P4
Seal tool

Hub
assembly

Hub
shoulder

Top of
seal

Apply
36765P
grease

Bottom
seal flange

Installing Drive Bell

1. Position new drive bell over transmission output

shaft. Rotate drive bell until splines in drive bell
line up with splines on transmission output shaft.

2. Screw

7

/

16

" bolt into transmission output shaft until

it bottoms out.

3. Using a wrench or socket, tighten bolt

CLOCKWISE to force drive bell down onto
transmission shaft until drive bell bottoms out on
shaft. Tighten new shoulder screw between 60 to 80
inch-pounds.

4. Place new plug over hole in drive bell and firmly

press into place using the palm of your hand.

NOTE: It may be necessary to insert the end of a paper

clip or thin blade screwdriver along side of plug
as it is pressed into drive bell to release
entrapped air.

NOTE: When fully seated plug should not extend above

drive bell more than 1/8 inch (3.2 mm).

5. Place agitator on top of drive bell. Slowly rotate

agitator until fingers on underside of agitator line
up with large slots on drive bell.

6. A sharp blow on top of agitator, with the palm of

your hand, will force agitator down onto drive
bell, allowing fingers on underside of agitator to
lock under bottom edge of drive bell. Do not push
agitator onto drive bell any further than necessary.

NOTE: Failure to lubricate the seal will cause the

washer to squeak in agitation.

«
...
25
26
27
28
29
...
»

Содержание WDSS4120















































Отзывы:

Нет отзывов