manualshive.com logo in svg

GE VR11, Справочное руководство

Поделиться
Скачать
GE VR11 Скачать руководство пользователя страница 70

Graphics Controller 

The ATI Mobile X300 Graphics Controller has the following features: 

•

 

Highly integrated Flat Panel and CRT GUI 

•

 

Max. pixel clock 300 MHz - 400 MHz 

•

 

Dual Independent Display for CRT front and CRT/Flat Panel rear 

•

 

CRT resolution up to 1600x1200, DVI up to 1600x1200 

 
 

Note: 

Termination resistors of the RGB lines are on the VR11 board for both front 
and rear interfaces. 
 
At higher resolutions the cable and connectors have great influence on picture 
quality. Use very good quality cables and connectors or reduce resolution to get 
a stable display of good quality. This is especially important for the highest 
resolution of 1600 x 1200. 
 
 

Software Installation 

The Technical Product Information CD-ROM supplied with the VR11 includes 
the most commonly used software drivers and utilities.  
 
 

PMC Interface 

The two PCI Mezzanine Card (PMC) Interfaces create an additional slot for 
parallel mounted expander or option cards. Please see chapter 'PCI Mezzanine 
Card (PMC)' of this manual for further details. 
 
 

Ethernet Interface 

The Ethernet controller 82571 from Intel used with the VR11 is a high 
performance dual Gigabit Ethernet 10/100/1000 Mbit PCI controller. Both 
channels are available on the VR11. Front or rear Ethernet can be selected 
when ordering. For registration and identification of a workstation in a LAN, a 
unique ID number is required. Each network card is assigned a unique ID 
number which resides in an Ethernet address ROM on the VR11. 
An Ethernet boot option can be enabled in BIOS setup. 
 
 

Software Installation 

The drivers available for the Ethernet controller 82571 support a large number 
of operating systems. The table shows operating systems supported by the 
available software: 
 

Table 22: Software interfaces 

Type  

System 

NDIS  

DOS 

NDIS  

Windows XP 

 

GE Intelligent Platforms – VR11, VP11 Hardware Reference Manual, Second Edition 

Page 70

 

Содержание VR11























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды