manualshive.com logo in svg

GE VR11, Справочное руководство

Поделиться
Скачать
GE VR11 Скачать руководство пользователя страница 28

Item Purpose 

VTM22 

Transition module, 4U x 4HE/HP 

VGA2DVI 

DVI to standard VGA converter 

YLR015RS 

RJ45 to 9-pin Sub-D cable 

 
Please contact the GE Intelligent Platforms sales department or your sales 
representative for latest information on options and accessories. 
 
Accessories are subject to change without notice. 
 
 

ESD

 

Electrostatic Discharge Notice

 

The discharge of static electricity, known as Electro Static Discharge or ESD, is 
a major cause of electronic component failure. The VR11 has been packed in a 
static-safe bag which protects the board from ESD while the board is in the bag. 
Before removing the VR11 or any other electronic product from its static-safe 
bag, be prepared to handle it in a static-safe environment. 
 

 

 
You should wear a properly-functioning anti static strap and ensure you are 
fully grounded. Any surface upon which you place the unprotected VR11 
should be static-safe, usually facilitated by the use of anti-static mats. From the 
time the board is removed from the anti-static bag until it is in the card cage 
and functioning properly, extreme care should be taken to avoid 'zapping' the 
board with ESD. You should be aware that you could 'zap' the board without 
you knowing it; a small discharge, imperceptible to the eye and touch, can often 
be enough to damage electronic components. Extra caution should be taken in 
cold and dry weather when static easily builds up. 
 
Only after ensuring that both you and the surrounding area are protected from 
ESD, carefully remove the board or module from the shipping carton by 
grasping it by the front panel and the connectors. Place the board, in its 
antistatic bag, flat down on a suitable surface. You may then remove the board 
from the anti static bag by tearing the ESD warning labels. 
 
 

Warning 

This is a Class A product. In a domestic environment, this product may cause 
radio interference in which case the user may be required to take adequate 
measures. 
 
 

GE Intelligent Platforms – VR11, VP11 Hardware Reference Manual, Second Edition 

Page 28

 

Содержание VR11























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды