background image

July  2003

8

PT878 Quick Start Guide

Powering ON and OFF

To operate the PT878, the power cord must be plugged into line 
voltage or the battery must be fully charged as described in 
Chapter 2, 

Initial Setup, 

of the 

User’s Manual. 

You must also 

install your transducers as discussed in the

 Liquid Transducer 

Installation Guide 

(document #916-055), and make transducer 

cable connections to the top of the PT878 as described in Chapter 
2 of the 

User’s Manual.

To turn the PT878 ON, press the red button in the upper-right-
hand corner of the keypad. Immediately upon power up the 
PT878 emits a short beep and displays a “PCI Loader” message. 
It then validates the instrument programming, displays the GE 
Panametrics logo and the software version, and emits a long beep. 
If the meter fails any of these tests, contact GE Panametrics.   

!WARNING!

 If the meter fails the backup battery test, you 

must send the unit back to the factory for a 

battery replacement. Make sure you keep the 

NiCad batteries charged until you are ready to 

ship the unit back to the factory. Before 

shipping, print out all the log and site data, or 

transfer it to your PC.

After the meter conducts all the self checks, the screen then 
appears similar to the one shown in Figure 2 on the next page. 

To turn the PT878 OFF, press the red key for 3 seconds. The 
screen now appears similar to Figure 3 on the next page. Three 
options are available:

Press 

[F1]

 to turn the PT878 completely OFF.

Press 

[F2]

 to send the PT878 into sleep mode. In this mode, 

some of the power supplies shut down, but the PT878 remains 
in a standby mode. Users can resume taking measurements 
immediately by pressing the power button.

Press 

[F3]

 to cancel the command and return the PT878 to 

normal operation.

Содержание Transport PT878
























Отзывы: