GE Solar 8000M/i Скачать руководство пользователя страница 63

Страница: 63 / 192

2026265-075C

Solar 8000M/i patient monitor

4-11

Maintenance and checkout:

Electrical safety tests

Ground (earth) wire leakage current tests

Perform this test to measure current leakage through the ground (earth)
wire of the equipment during normal operation.

The device under test is to be tested at its normal operating voltage.

1. Configure the leakage tester like the circuit shown below.

2. Connect the power cord of the device under test to the power

receptacle on the leakage tester.

3. Set the power switch of the device under test to ON.

4. Read the current leakage indicated on DMM.

5. Set the polarity switch on the leakage tester to RVS (reverse).

6. Read the current leakage indicated on DMM.

NOTE

If either reading is greater than the appropriate specification
below, the device under test fails. Contact GE Technical Support.

300

A (0.3 volts on the DMM), and the device under test is

powered from 100-120 V/50-60 Hz.

300

A (0.3 volts on the DMM), and the device under test is

powered from a centered-tapped 200-240 V/50-60 Hz, single
phase circuit.

500

A (0.5 volts on the DMM), and the device under test is

powered from a non-center-tapped, 200-240 V/50-60 Hz, single-
phase circuit.

NOTE

Center-tapped and non-center-tapped supply circuits produce
different leakage currents and the UL and EN limits are
different.

7. Set the power switch of the device under test to OFF.

Power Cord

Leakage Tester

NORM

RVS

HIGH

LOW

GND

0.015µF

Power Cord

Device

Under

Test

DMM set to measure AC voltage

GND

DMM

10K

500A

Содержание Solar 8000M/i

































































































































































































Результаты поиска

Содержание Solar 8000M/i

Отзывы:

Похожие инструкции для Solar 8000M/i

Бренды по названию

Популярные бренды

GE Solar 8000M/i, Руководство по обслуживанию

Результаты поиска

Содержание Solar 8000M/i

Отзывы:

Похожие инструкции для Solar 8000M/i

Бренды по названию

Популярные бренды