GE SmartWater GXCF05D, Руководство пользователя, Страница: 8 / 28

For long vacations or absences, set both power switches
(on the back of the dispenser, if equipped) to the O (off) position .
1. Unplug the water dispenser .
2. Remove the water bottle .
3. Drain the water tanks (see
Draining the Dispenser
) .
4. Dry the separator thoroughly on both the top and bottom (see
Cleaning the Separator
) .
5. Leave the door of the chiller compartment open
(on some models) .
After returning from vacation, make sure to sanitize the water tanks
before using the dispenser (see Cleaning and Sanitizing the Water Tank).
Preparing for Vacation
Chilling Rate: approx . 0 .5 gallons (2 liters) per hour
Heating Rate: approx . 0 .8 gallons (3 liters) per hour
Capacity: 3 or 5 gallon bottle
Power Consumption: Heating: 480 watts max .
Cooling: 125 watts max .
Specifications
Defrosting
(GXCF20E/GXCF20FBB/GXCF20KWW/GXCF20KBB Chiller Model)
Defrost whenever frost on the wall of the chiller compartment
becomes
excessive. Never use a sharp or metallic instrument to remove
frost as it may damage the liner. We recommend using a plastic
scraper.
Do not use any electrical device in defrosting your chiller
compartment.
To defrost:
n
Remove items from the compartment .
n
Turn the Cold Power switch (if equipped) to off and unplug the
dispenser .
n
Put several towels in the bottom of the compartment
to collect water .
Defrosting usually takes a few hours . To defrost faster,
keep the door open .
After defrosting:
n
Remove the wet towels and wipe up any remaining water .
n
Wipe the compartment with a dry cloth .
n
Plug in the unit and turn on the Cold power switch
(if equipped) . Return items to the unit .
Troubleshooting Tips.
Problem Possible Causes What To Do
Water has poor taste Separator needs cleaning. •­See­ Cleaning the Separator.
or odor
Unit needs to be sanitized. •­See­
Cleaning and Sanitizing the Water Tanks.
Water not hot enough Dispenser is unplugged.­ •­Push­the­plug­completely­into­the­outlet.
or cold enough
The fuse is blown/circuit ­ •­Replace­house­fuse­or­reset­the­house­circuit­breaker.
breaker is tripped. •­If­too­many­items­are­plugged­into­a­single­circuit,­move
some items to a different circuit .
All the water in the water tank ­ •­Wait­30­minutes­for­water­to­heat­or­cool.
has been used.
Temperature limiter tripped. ­ •­Set­the­hot­and­cold­power­switches­(on­the­back­of­the­
dispenser) to the O (off) position . Wait five minutes; then
set the switches to the I (on) position . Wait 30 minutes for
water to heat or cool .
Water dispenser does Empty water bottle. •­Replace­with­a­new­bottle­of­water.
not work – No water flow
Mineral deposits clogging tanks.­ •­See­ Care and Cleaning .
Cold water button Chiller door has been left open. •­Close­chiller­door.
does not dispense
Ice buildup blocking water flow.­ •­Turn­off­cold­power­switch­(if­equipped)­or­unplug­unit­­ ­
overnight . Once water can be dispensed from faucet, plug
unit back in or turn cold power switch back to the ON position .
Water dispenser leaks Crack or pin hole in bottle. ­ •­Replace­with­a­new­bottle­of­water.
from the outside
Compressor does not start
Normal Operation—Compressor •­Wait­for­up­to­3­minutes­for­the­compressor­to­start.
when unit is plugged in start is delayed by up to 3 minutes
and cold power switch to prolong the compressor life.
(if equipped) is on.
Bottle feels warm
Water system overfilled. •­Dispense­cold­water­until­air­is­released­into­the­bottle.
Water is boiling in the hot tank
and bubbling up into the bottle.
Care and cleaning of the dispenser.
8