manualshive.com logo in svg

GE PROFILE PDE9900, Техническое обслуживание руководство

Поделиться
Скачать
GE PROFILE PDE9900 Скачать руководство пользователя страница 28

– 28 –

Active Vent 

The active vent consists of the fan, motor, housing, 
and vent louver motor.

The active vent helps to reduce the noise level and 
heat loss when in the closed position. The control 
module su/- 12 VDC to the vent louver 
motor. The control module reverses polarity to drive 
the motor in a clockwise or counterclockwise (open 
or closed) direction.

The vent closes 8 seconds after the main pump 
is switched on during the fi rst fi ll cycle and opens 
during the drying cycle (heated and non-heated).  
The vent is open during cooldown periods or when 
the unit is not in use.

If the vent is closed and the door is opened during 
the wash cycle, the vent will open. When the door 
is closed again, the vent will remain open for 8 
seconds, then close again to fi nish the cycle.

It is normal for water vapor to come through the 
active vent during the dry cycle. The active vent can 
be opened and closed using the 

Service Mode

.

The vent louver is held in place by a single screw.

Remove the motor from the mount by rotating the 
motor 90° in the mount and sliding it out between 
the tabs.

Note: 

The gear in the mount is held in place with the 

motor. 

Vent Motor Strip Circuit

J5-2

RED

BLK

M

J5-1

 

Note:

 Foam with double-sided tape holds the 

conduit in place. The foam tears easily if pulled 
during removal of the housing.

Six Phillips head screws hold the fan and motor to 
the vent housing. 

Fan Motor Strip Circuit

65 W

FAN

DK. BLUE/RED

M

WHITE

J2-3

Note:

 This also applies to the 

Rinse Only

 cycle. 

Since heated dry is not an option with 

Rinse Only

, 

the fan will run for approximately 4 hours before 
turning off.

To access the vent fan and motor, remove the door 
panel (see 

Door Panel

).

The vent fan and motor housing are held in place 
by:

•  4 long, silver Phillips head screws.

•  2 short, brass Phillips head screws (see photo).

Fan

 (PDW9700 AND PDW9900 Series)

During natural dry, the fan runs for approximately 
4 hours after the last drain cycle is completed 
(clean light on). During heated dry, the fan runs for 
approximately 2 hours after the last drain cycle is 
completed. If the door is opened, the fan stops and 
the control stops counting down. When the door is 
relatched, the fan will start again and the control will 
continue to count down. Touching any key will turn 
off the fan.

Содержание PROFILE PDE9900






































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды