manualshive.com logo in svg

GE PCVH480EKWW Series, Руководство по обслуживанию, Страница: 51 / 53

Поделиться
Скачать
GE PCVH480EKWW Series Скачать руководство пользователя страница 51

Service Test Mode (cont.)

Service Mode test

Sequence

Note

Start/Pause

Displays software version number.

t01

Software version

Power

Returns to service mode screen.

Start/Pause

Displays error codes.

Start/Pause

Clears highlighted error code from 
machine (during t02 test).

t02

Error codes

Power

Returns to service mode screen.

Start/Pause

LEDs light up.

Any button but 
Power

Hear beep as button is pressed 
(during t03 test).

t03

User interface test

Power

Returns to service mode screen.

Start/Pause

Displays shall show “dO or OO”.

t04

Door switch test

Power

Returns to service mode screen.

“dO”: Door is open.
“OO”: Door is closed. 

Start/Pause

Dryer motor will rotate.

t05

Dryer motor test

Power

Returns to service mode screen.

“on”: Motor rotate.
“dO”: Door is open.

Start/Pause

Displays temperature & dryer motor 
will rotate.

t06

Thermistor & 1600W heater test

Power

Returns to service mode screen.

The heater shall then 
be turned on for a 
maximum of 5 minutes.

Start/Pause

Displays temperature & dryer motor 
will rotate.

t07

Thermistor & 600W heater test

Power

Returns to service mode screen.

The heater shall then 
be turned on for a 
maximum of 5 minutes.

Start/Pause

Displays the status of touch sensors.

t08

Moisture sensor test

Power

Returns to service mode screen.

Touch the sensor with 
hand “1” : be detected
“0”: Is not detected.

Содержание PCVH480EKWW Series






















































Отзывы:

Нет отзывов