GE PCIE-5565PIORC* Скачать руководство пользователя страница 38

Страница: 38 / 70

38 PCIE-5565PIORC Reflective Memory Board

Table 3-22 PCI Interrupt Line

PCI Interrupt Line: PCIILR, Offset $3C

Bit

Description

Read

Write

*Value after

PCI Reset

7:0

Interrupt Line Routing Value.

Value indicates which input of the system

interrupt controller(s) is connected to each interrupt line of the device.

Yes

NOTE:

This register will be altered by the system BIOS during the system boot process.

Table 3-23 PCI Interrupt Pin

PCI Interrupt Pin: PCIIPR, Offset $3D

Bit

Description

Read

Write

Value after

PCI Reset

7:0

Interrupt Pin Register.

Indicates which interrupt pin the

device uses. The following values are decoded (the
Reflective Memory supports only INTA#).

1 = INTA#
2 = INTB#
3 = INTC#
4 = INTD#

Yes

Table 3-24 MSI Capability Structure

Offset 31::16

15:8

7:0

0x050 Message Control

0x78 (next cap ptr)

0x05 (capability ID)

0x054

Message Address

0x058

Message Upper Address

0x05C

Reserved

Message Data

Table 3-25 Message Control bit definition

Message Control bit definition: Offset 0x050

Bit(s)

Field

Description

R/W

15:9

Reserved

R/W

Mask Capability

Not Supported. Hardwired to 0

64-bit Address Capability Not Supported. Hardwired to 0

6:4

Multiple Message Enable Indicates the number of MSI signals

allocated by system software.
- 000: 1MSI allocated
- 001: 2 MSI allocated
- 010: 4 MSI allocated
- 011: 8 MSI allocated
- 100: 16 MSI allocated
- 101: 32 MSI allocated
- 110: Reserved
- 111: Reserved

R/W

3:1

Multiple Message
Capable

Indicates the number of requested MSI
messages
- 010:4 MSI allocated

MSI Enable

1= MSI Enabled

R/W

Содержание PCIE-5565PIORC*







































































Результаты поиска

Содержание PCIE-5565PIORC*

Отзывы:

Похожие инструкции для PCIE-5565PIORC*

Бренды по названию

Популярные бренды

GE PCIE-5565PIORC*, Справочник по аппаратуре

Результаты поиска

Содержание PCIE-5565PIORC*

Отзывы:

Похожие инструкции для PCIE-5565PIORC*

Бренды по названию

Популярные бренды