background image

Installation

Dual Burner Outdoor Cooktop

• All built-in installations should be at least

35-1/2" above the floor.

Clearances to Combustibles:

• Allow at least 6" clearance from the back and

sides to any combustible material.

• Allow at least 1" clearance below the cooking

surface on all sides.

Installation in a combustible enclosure:

• Installation into a combustible enclosure

requires the ZX2JYSS insulated jacket.

• The insulated jacket must be supported from

the bottom by a solid deck or ledge on each
side beneath the jacket.

6

2

A

Installation
Into An
Enclosure

(Skip this step
if burner is installed
on a grill cart)

Step

Installation in a non-combustible enclosure:

• In a non-combustible (masonry) enclosure,

the burner drops into the opening. A solid
deck beneath is required for support from
the bottom.

Combustible enclosure with Insulated Jacket

Non-combustible enclosure

To install trim kit ZX2TKYSS:

• Remove the cover and burner grate.
• Place side trim and rear trim pieces over the

burner edges, overlapping the countertop
surface.

• Install screws from the inside of the burner

and through the trim. 3 each on all sides.

NOTE: The trim kit is not designed to support
the weight of the Dual Range Top Burner.
Support from the bottom must be provided.

24-5/8"

11"

2x2 
Opening 
for Gas 
Supply 
Line

1-1/8"

1"

15-3/8"

23-5/8"

10-3/8"

13-1/8"

2x2 
Opening 
for Gas 
Supply 
Line

Содержание Monogram ZX2L SS













Отзывы: