GE Monogram ZV900 Скачать руководство пользователя страница 7

Страница: 7 / 21

Installation Preparation

REMOVE THE PACKAGING

CAUTION:

LIFT THE HOOD OUT OF THE BOX

BY THE CENTER METAL PORTION. DO NOT LIFT BY THE
GLASS SIDES.

PRUDENCE :

LEVEZ LA HOTTE À

L’EXTÉRIEUR DE LA BOÎTE PAR LA PORTION MÉTAL
CENTRAL. NE LEVEZ PAS PAR LES CÔTÉS DE VERRE.

CAUTION:

Wear gloves to protect against

sharp edges.

PRUDENCE :

Portez des gants pour éviter

les blessures causées par les tranchants.

•

Grasp the hood by the metal insert in the center
and lift straight up and out of the box.

•

Remove and properly discard the plastic wrapping.

•

Remove parts box, duct covers and other
packaging.

TOOLS AND MATERIALS REQUIRED

(NOT SUPPLIED

)

Tape measure

Knife

Spirit level

Wire cutter/stripper

Wire nuts

Electric drill with 5/16

″

and 3/8

″

bits

Phillips and flat blade screwdrivers

Hammer

Pliers

Safety glasses

Duct tape

Tape to mount template

Gloves to protect against sharp edges

120V 60Hz. 15 or 20 Amp, 2 wire with
ground Properly grounded branch circuit

Strain relief for junction cover

″

round metal duct, length to suit

installation

Saw, jig saw or reciprocating saw

Measuring tape

Electric drill
with 5/16” and
3/8” Bits

12” long
Phillips
head
screwdriver

Safety glasses

Gloves

Spirit level

Knife

Wire

cutter/stripper

Flat blade

screwdriver

Hammer

Pliers

Duct tape

Masking tape

Wire nuts

Strain relief

Saw, jig saw or

reciprocating

saw

″

round metal duct,

length to suit

installation

Содержание Monogram ZV900






















Результаты поиска

Содержание Monogram ZV900

Отзывы:

GE Monogram ZV900, Руководство по установке, Страница: 7 / 21

Результаты поиска

Содержание Monogram ZV900

Отзывы: