7
Installation Instructions
REMOVE PACKAGING
CAUTION:
Refrigerator is much heavier at the top than at
the bottom—be careful when moving. When using a hand truck,
handle from side only.
PRUDENCE :
Le réfrigérateur est beaucoup plus lourd
en haut qu'en bas. Il faut être prudent lors des déplacements.
Si un diable est utilisé, il faut soulever le réfrigérateur sur le côté
seulement.
• Carefully cut banding at the top and bottom, remove outer
carton.
• Slide out back corner posts (2).
• Slide carton off top of cabinet.
NOTE:
IT IS NOT NECESSARY TO LAY CABINET DOWN IN ORDER
TO REMOVE SKID!
• The unit is secured to the skid with 4 slotted tie-down straps.
Remove the four 5/16
″
bolts from the base channels in the
tie-downs.
• Remove the four 7/16
″
bolts securing the straps
to the skid.
CAUTION:
DO NOT
ATTEMPT TO ROLL UNIT
OFF SKID.
PRUDENCE :
IL NE FAUT PAS ESSAYER
DE FAIRE ROULER LE
RÉFRIGÉRATEUR POUR
L'ENLEVER DE LAY PALETTE.
• Support blocks on the bottom of the refrigeration case must
be removed before the refrigerator is taken off the skid or
damage will occur. Carefully tilt refrigerator and slide blocks
out from beneath.
• Remove the tape from the leveling legs.
• Lift the refrigerator off the skid with an appliance dolly.
Handle from the sides.
1
Remove
Tie-Downs
INSTALL WATER LINES
• A cold water supply is required for automatic icemaker
operation. The water pressure must be between 40 and 120
p.s.i.
• Route 1/4
″
OD copper or GE SmartConnect
™
plastic tubing
between house cold water line and the water connection
location.
• Tubing should be long enough to extend to the front of the
refrigerator. Allow enough tubing to accommodate bend
leading into the water line connection.
NOTE:
The only GE approved plastic tubing is supplied in
the GE SmartConnect
™
Refrigerator Tubing kits. Do not use
any other plastic water supply line because the line is under
pressure at all times. Other types of plastic may crack or
rupture with age and cause water damage to your home.
GE SmartConnect
™
Refrigerator Tubing Kits are available in the
following lengths:
2
′
(.6 m) WX08X10002
6
′
(1.8 m) WX08X10006
15
′
(4.6 m) WX08X10015
25
′
(7.6 m) WX08X10025
Shut off the main water supply.
Turn on the nearest faucet long enough to clear the line of
water.
• Install a shut-off valve between the icemaker water valve and
cold water pipe in a basement or cabinet. The shut-off valve
should be located where it will be easily accessible.
• Turn on the main water supply and flush debris.
Run about a quart of water through the tubing into
a bucket. Shut off water supply at the shut-off valve.
NOTE:
Saddle type shut-off valves are included in many water
supply kits. Before purchasing, make sure a saddle type valve
complies with your local plumbing codes
.
If the water supply to the refrigerator is from a Reverse
Osmosis Water System, use the refrigerator’s filter bypass
plug. Using the refrigerator’s water filtration cartridge with
the RO filter can result in hollow ice cubes
.
2
NOTE:
Commonwealth of Massachusetts Plumbing Codes
248CMR shall be adhered to. Saddle valves are illegal and use
is not permitted in Massachusetts. Consult with your licensed
plumber.
Floor
Filter Bypass Plug
Waterline Tubing
Содержание Monogram ZICP720
Страница 19: ...19 Notes ...
