background image

Design Guide

PRODUCT CLEARANCES

The stainless steel wine chiller, wine reserve and 
beverage center is factory set for a 110° door swing. 
Models that accept custom panels have a 95° door 
swing.

When installed in a corner:

• 

Allow 4"

 

min. clearance on the hinge side for the 90° 

door swing and to allow racks to slide out.

• Allow 10" minimum clearance on the hinge side for 

a full 110° door swing. (Models ZDWI240WII and 
ZDBI240WII have a 95° door swing.)

NOTE: 

Custom handle clearances may vary, depending 

on custom handle depth. 

• The door swing is reversible on all models. If desired, 

change the door swing before installation or before 
installing the custom frame panel.

Choose the location:

• These products may be closed in on the top and 

three sides as long as the front is unobstructed for air 
circulation and proper access to the door.

• Do not install these products where the temperature 

will go below 55°F (13°C) or above 90°F (32°C).

• Do not install where it will be subject to direct sunlight,  

heat or moisture.

• These products are not designed to be stacked one 

over the other.

Black or Stainless Steel Toekick Options

• These products are shipped with a black toekick 

installed. An optional stainless steel toekick is also 
supplied with each product. For shipping purposes, the 
stainless steel toekick is secured to the back of the unit.

4

90° Door Swing

SIDE-BY-SIDE INSTALLATIONS

Increase storage capacity by installing two Monogram 
beverage centers, wine chillers or wine reserves together. 
Or, for a complete refreshment center, install any two  
of these units together.
• A side-by-side installation requires at least a 47-1/2"-

wide minimum opening for standard installation and 
a 48-1/2"-wide minimum opening for flush installation 
of stainless steel models. A 49-1/2"-wide minimum 
opening is required for side-by-side flush installation  
of custom framed models. 

• Products must operate from separate, properly 

grounded receptacles.

502Dia21

10" Minimum

to Wall

110

°

*

*95

°

 Door Swing on Custom Frame Models

21-5/8"

23-5/8"

615Dia8

4" Minimum

to Wall

90

ϒ

Содержание Monogram ZDBI240









Отзывы: