GE Monogram ZDB24 BB Скачать руководство пользователя страница 5

5

To remove the door:

• Remove the top hinge pin using a 1/8" Allen

wrench. Set aside.

• Lift the door off the bottom hinge.
• Remove the top hinge and set aside.
• Remove the bottom hinge, the plastic washer

and the bottom hinge pin using a Phillips
screwdriver.

• Install the Phillips hinge pin in the top

hinge and re-install the top hinge on the
bottom left side.

• Re-install the plastic washer over the hinge

pin.

• Install the Allen wrench hinge pin in the

bottom hinge and re-install the bottom
hinge on the top left side.

• Insert the supplied plug buttons into the old

hinge holes, top and bottom.

The light trigger on the bottom of the door
must be removed and secured to the opposite
end.
• Remove the light trigger by backing out 2

screws. Set the trigger and screws aside.

• Install screws from plastic bag packed with

Owner’s Manual into light trigger holes.

• Turn the door upside down.
• Measure and mark 12-1/4" and 13" from the

right side (or 3/4" from the first location).
Measure and mark 11/16" from the front
side of the door. See illustration.

• Drill holes with 5/32" drill bit.
• Install the light trigger with original screws.
• Remove the top hinge pin using the 1/8"

allen wrench.

• Place the door onto the bottom hinge, and

install the top hinge pin with allen wrench.

• Open and close door to test door swing. If

door drags and does not close evenly, loosen
hinge screws and slip shims behind the
hinge. Tighten screws and test again.

Position new nameplate:

• Remove the original nameplate, now located

on the bottom of the door.

• Locate the template on the back of this

instruction book.

• Hold or tape template behind glass door.
• Remove backing from Monogram name-

plate.

• Place nameplate onto front side of door,

matching illustration on template.

Reverse
Door
Swing

Installation Preparation

Beverage Center & Wine Chiller

Top Hinge

Bottom Hinge

Light Trigger

Top of the Door

12-1/4"

Front of the Door

3/4"

11/16"

Slip Shim
Behind Hinge

Top of Name Plate

Top of Glass Door

Door Frame Side

P/N 41005263

Upper Left
Corner of
Glass

DOOR

NAME PLA

TE

LOCATION

Содержание Monogram ZDB24 BB









Отзывы: