GE Mini COM Express 10 Скачать руководство пользователя страница 68

Страница: 68 / 82

6.9.2

Control

The I

C run-time Control register is used to enable and disable the core, and to enable and

mask its interrupt.

C Control Register (Offset 0x2)

Bit

Name

Access

Default

Description

R/W

Controller core enable

0: I2C controller is disabled
1: I2C controller is enabled

IEN

R/W

Interrupt enable

0: External interrupt is disabled

(masked)

1: External interrupt is enabled

(unmasked)

—

0b000000

Reserved

6.9.3

Transmit

The I

C Transmit register is used to write the data and address/control bytes to be sent on

the I

C bus. It can be written at address offset 0x3 and read back at offset 0x5.

C Transmit Register (Offset 0x3/0x5)

Bit

Name

Access

Default

Description

7:0

R/W

0x00

Data or address/control byte to

be transmitted on the I

C bus

6.9.4

Receive

The I

C Receive register is used to retrieve the data bytes received from the I

C bus.

C Receive Register (Offset 0x3)

Bit

Name

Access

Default

Description

7:0

0x00

Data received from the I

C bus

GFK-2896

Mini COM Express Type 10 Module mCOM10-L1500

For public disclosure

Содержание Mini COM Express 10



















































































Результаты поиска

Содержание Mini COM Express 10

Отзывы:

Похожие инструкции для Mini COM Express 10

Бренды по названию

Популярные бренды

GE Mini COM Express 10, Справочник по аппаратуре

Результаты поиска

Содержание Mini COM Express 10

Отзывы:

Похожие инструкции для Mini COM Express 10

Бренды по названию

Популярные бренды