49-85220-2
31
Problem
Possible Cause
What To Do
Oven light does not
ZRUN
Light bulb is loose or defective.
Tighten or replace bulb. See the Maintenance section for
instructions on how to replace the bulb.
2YHQZLOOQRWVHOIFOHDQ
The temperature is too high to set
a self-clean operation.
Allow the oven to cool.
Oven controls improperly set.
See the Cleaning the Oven section.
([FHVVLYHVPRNLQJ
during clean cycle
([FHVVLYHVRLORUJUHDVH
Press the
&DQFHO2II
pad. Allow the oven to cool below
WKHXQORFNLQJWHPSHUDWXUH:LSHWKHH[FHVVVRLODQG
reset the clean cycle.
Oven not clean after a
clean cycle
Oven controls improperly set.
See the Cleaning the Oven section.
2YHQZDVKHDYLO\VRLOHG
Clean up heavy spillovers before starting the clean cycle.
Heavily soiled ovens may need to self-clean again or for
a longer period of time.
Strong “burning” or
“oily” odor emitting
from the vent
7KLVLVQRUPDOLQDQHZRYHQDQG
ZLOOGLVDSSHDULQWLPH
To speed the process, set a self-clean cycle for a
minimum of 3 hours. See the Cleaning the Oven section.
This is temporary.
([FHVVLYHVPRNLQJ
during broiling
Food too close to burner element.
/RZHUWKHUDFNSRVLWLRQRIWKHIRRG
2YHQODWFKZLOOQRWRSHQ
The temperature inside the
RYHQKDVQRWGURSSHGEHORZWKH
unlocking temperature.
Press the
&DQFHO2II
pad. Allow the oven to cool below
the unlocking temperature.
/2&.'225IODVKHV
in the display
The self-clean or steam-clean cycle
has been selected but the door is
not locked.
/RFNWKHRYHQGRRU
“F— and a number
or letter” flash in the
display
You have a function error code.
Press the
&DQFHO2II
pad. Allow the oven to cool for one
hour. Put the oven back into operation. If the function code
repeats, disconnect all power to the oven for at least 30
seconds and then reconnect power. If the function error code
repeats again, call for service.
Clock flashes due to a
SRZHURXWDJH
3RZHURXWDJHRUVXUJH
Reset the clock. If the oven was in use, you must reset
it by pressing the
&DQFHO2II
pad, setting the clock and
resetting any cooking function.
Lock Controls or
Control Lockout feature
is activated
If
LOC ON
appears in the display, the range control is
locked. Turn this feature off to use the range. See the
Oven Controls section.
Surface Burners do not
light
Plug on range is not completely
inserted in the electrical outlet.
Make sure electrical plug is plugged into a live, properly
grounded outlet.
Gas supply not connected or
turned on.
See the Installation Instructions that came with your
range.
$IXVHLQ\RXUKRPHPD\EHEORZQ
or the circuit breaker tripped.
Replace the fuse or reset the circuit breaker.
Burner parts not replaced correctly.
See the Care and Cleaning section.
%XUQHUVORWVQHDUWKHHOHFWURGHRU
the round lighter port on the oval
EXUQHUPD\EHFORJJHG
Remove the burners and clean them. Check the
electrode area for burned-on food or grease. See the
Care and Cleaning section.
Food residue on electrode
/LJKWO\SROLVKIODWWLSRIHOHFWURGHZLWKQDLOILOHRU
sandpaper until shiny.
Troubleshooting tips ... Before you call for service
TR
OUBLESHOO
TING TIPS
Содержание JGB700SEJ4SS
