GE Homespring UF 211, Руководство по эксплуатации, Страница: 31 / 37

31
Some water may still remain in the System. Plug
the Inlet, Outlet, and Drain ports immediately
once the pipe assemblies have been removed.
9. Using the Cap Wrench, remove the System
Cap.
10. Remove the Internal Prefilter from the
System. Set the Internal Prefilter aside in a
clean area for reuse.
11. Unscrew the Locking Clip screw and remove
the Locking Clip.
12. Unscrew the System Casing from the
Backpulse Tank using a strap wrench.
13 If under warranty, the old System must be
completely sealed, packaged and returned to
the factory within 24 hours to avoid internal
damage and allow a cause analysis to be
completed.
14. Label the box appropriately as in the table
below. Call the GE Homespring Consumer
Products Customer Service for shipping and
handling details at 1-866-418-7412.
15. Remove the new replacement module from
the packaging. Screw it onto the Backpulse
Tank.
16. Reattach the Locking Clip, Air Relief Valve,
Inlet / Outlet / Drain pipe assemblies, Internal
Prefilter, System Cap, External Prefilter (if
applicable), and Controller.
17. Reconnect the System to the house
plumbing and the drain. Follow F.
COMMISSIONING to start up the System again.
Follow steps 18 to 31 for Horizontally-
mounted Systems:
18. Attach a 1/4" tubing to the Inlet Mini Ball
and direct the other end to a large pail. Open
the Mini Ball Valve to drain the water inside the
Internal Prefilter cavity. Remove the 1/4" tubing
from the Mini Ball Valve.
19. Remove the Metal Support Strap.
20. Remove the Air Relief Valve, the Air Vent
Assembly, the Inlet pipe assembly, the Outlet
pipe assembly, and the Drain line assembly
from the System. Removal of the Inlet pipe
assembly and the Outlet pipe assembly may
require disconnecting the Inlet line and Outlet
line at multiple places.
21. Using the Cap Wrench, remove the System
Cap.
22. Unscrew the Locking Clip Screw and remove
the Locking Clip.
23. Using a strap wrench, loosen the System
casing from the Backpulse Tank. Do not detach
the System casing from the Backpulse Tank
completely.
24. Unscrew the two bolts securing the bottom
of the Backpulse Tank to the End Cast Iron
Stand.
25. Remove the entire System from the
Horizontal Mounting Bracket and stand the
System upright on the floor.
26. Remove all the Inlet, Drain, and Air Relief
Valve plugs from the new System and insert
those plugs into the equivalent ports of the old
System.
27. Remove the Internal Prefilter from the
System. Set the Internal Prefilter aside in a
clean area for reuse.
28. Unscrew the System Casing from the
Backpulse Tank.
29. If under warranty, the old System must be
completely sealed, packaged and returned to
the factory within 24 hours to avoid internal
damage and allow a cause analysis to be
completed.
30. Label the box appropriately as in the table
below. Call the GE Homespring Consumer
Products Customer Service for shipping and
handling details at 1-866-418-7412.
31. Partially screw the new System Casing on
the Backpulse Tank by hand. Do not use a strap
wrench.
32. Lift and place the System on the Horizontal
Mounting Bracket. Reattach the Backpulse Tank
to the End Cast Iron Stand. Once finished,
tighen the System Casing on the Backpulse
Tank by hand.
33. Reattach the Locking Clip, Air Relief Valve,
Inlet / Outlet / Drain pipe assemblies, Internal
Prefilter, System Cap, External Prefilter (if