GE GSD1300N Скачать руководство пользователя страница 15

Страница: 15 / 16

Figure AA

Dishwasher Installation

STEP 20: REPLACE ACCESS PANEL AND

TOEKICK

In this step you will need the panels and the two

screws set aside in Step 4.

There are two types of screws used. The 8-32 x 1/4"
screws are used at the top of the access panel and
should still be in place. The 10-16 x 3/8" screws are
used at the bottom of the access panel and secure
both the access panel and toekick.

IMPORTANT –

Screws are not

interchangeable

To prevent damage to your

dishwasher, use the proper screw in the proper

location. Do not mix screw types or lengths.

• Place the toekick against the legs of the

dishwasher.

• Remove the two 8-32 x 1/4" machine thread

screws.

• Align the access panel to the dishwasher.
• Select the two 8-32 x 1/4" machine thread screws

just removed and insert them through the top
holes in the access panel and into the dishwasher
frame.

• Tighten these screws.
• Align the toekick and make sure the bottom edge

is against the ﬂoor.

• Insert and tighten the two 10-16 x 3/8" sheet metal

thread screws, making sure the bottom edge of
the toekick stays in contact with the ﬂoor.

STEP 21: LITERATURE

■

Leave the Owners’ Manual, Installation

Instructions, samples, and/or coupons with
consumer.

Tip: Prevent tub damage and reduce sound from

under the dishwasher

Use the machine thread screws in the top holes and
the sheet metal thread screws in the bottom holes.
Make sure the toekick is against the floor.

Access Panel

oekick

Remove, then Reinstall and Tighten

8-32 x 1/4”

Machine Thread Screws

Install and Tighten

10-16 x 3/8”

Sheet Metal Thread Screws

Содержание GSD1300N

















Результаты поиска

Содержание GSD1300N

Отзывы:

Похожие инструкции для GSD1300N

Бренды по названию

Популярные бренды

GE GSD1300N, Руководство по установке

Результаты поиска

Содержание GSD1300N

Отзывы:

Похожие инструкции для GSD1300N

Бренды по названию

Популярные бренды