49-5000090
5
Using the Air Conditioner
USING THE
A
IR CONDITIONER
Remote Control
Ŷ
To ensure proper operation, aim the remote control at the
signal receiver on the air conditioner.
Ŷ0DNHVXUHQRWKLQJLVEHWZHHQWKHDLUFRQGLWLRQHUDQG
the remote control that could block the signal.
Ŷ
The remote control signal has a range of up to 20 feet.
Ŷ0DNHVXUHEDWWHULHVDUHIUHVKDQGLQVWDOOHGFRUUHFWO\DV
indicated on the remote control.
Ŷ5HPRWHFRQWDLQVDPDJQHWDOORZLQJLWWRDWWDFKWRPHWDO
surfaces.
Do Not Operate in Freezing Outdoor Conditions
This cool-only air conditioner was not designed for freezing outdoor conditions. It must not be used when the outdoor
temperature is below freezing (32°F).
Cool Mode
8VHWKH&RROPRGHDW/RZ0HG+LJKRU$XWR)DQ
6SHHGIRUFRROLQJ8VHWKH7HPSHUDWXUH,QFUHDVH
Decrease - pads to set the desired temperature between
64°F and 86°F in 1°F increments.
An electronic thermostat is used to maintain the room
temperature. The compressor will cycle on and off
to keep the room at the set level of comfort. Set the
thermostat at a lower number and the indoor air will
become cooler. Set the thermostat at a higher number
and the indoor air will become warmer.
NOTE:
If the air conditioner is off and is then turned on
while set to a
Cool
setting or if turned from a fan setting
to a
Cool
VHWWLQJLWPD\WDNHDSSUR[LPDWHO\PLQXWHVIRU
the compressor to start and cooling to begin.
Cooling Descriptions
For Normal Cooling—
Select the
Cool
mode and
High
or
Med
fan with a middle set temperature.
For Maximum Cooling—
Select the
Cool
mode
and
High
fan with a lower set temperature.
For Quieter and Nighttime Cooling—
Select the
Cool
mode and
Low
fan with a middle set temperature.
ECO Mode
This mode optimizes the cooling power of your air
conditioner, thereby saving you energy. Once the set
point temperature has been reached, the fan will cycle
off to save energy. The fan will cycle back on periodically
to insure all cooling capacity in the system is used. This
mode is the default mode for the unit. Each time the
unit is powered off, it will restart in
ECO
mode
ON
. This
includes
Delay
timer mode. The first time the unit is
turned on, the settings will be 70° and
Low
fan. You can
adjust the fan speed and temperature to your personal
comfort.
ON—
The fan will cycle on and off with the compressor.
This may result in wider variations of room temperature
and humidity. NOTE: the fan may continue to run
for a short time or may pulse intermittently after the
compressor cycles off to sample the room air.
OFF—
The fan runs all the time, while the compressor
cycles on and off.
Control Display On and Off
To reduce brightness during sleeping hours, this
air conditioner control display has an automatic
off feature where the control display will turn
off completely after 5 minutes of inactivity. To
illuminate the control interface, press any button on
the control display or remote control. The control
display will illuminate all previously illuminated
LED’s. The control interface will now respond to
any prescribed button press after it is illuminated.
Press and hold the FAN+MODE buttons
simultaneously to toggle this feature ON or OFF. The
LED’s will now stay ON anytime the unit is ON.
Control sound on/off
This air conditioner will make a beep when the buttons
on the control are pushed or if the unit receives a
command from the mobile app or remote control. To
silence these beeps, simultaneously press the FAN
and “-” buttons for 3 seconds. Press these buttons
again to toggle the sound back on.