GE Drawer Freezer Refrigerator Скачать руководство пользователя

Страница: 9 / 16

STEP 6 REMOVE THE TOEKICK

If, after removing the freezer drawers and
refrigerator door, the refrigerator will still
not fit through a doorway, the toekick
can be removed.

• Remove the toekick by removing the 2 Phillips

head screws.

STEP 7 MOVE THE REFRIGERATOR

• Place a piece of the carton or soft cloth against

the side panel of the refrigerator to pad and protect
the stainless steel finish.

• Place the refrigerator on the handtruck

with a side

against the truck only

• Move the refrigerator indoors. Place refrigerator close

to the installation location.

REPLACE THE FREEZER BASKET

Replace the top drawer freezer basket.

Drive the bottom outside screw into the door

on each side until it is all the way in.

Drive the remaining 3 screws on each side
all the way into place (there are a total
of 8 hex-head screws).

Screw

Screws

TOP DRAWER

STEP 8 REPLACE THE FREEZER

DRAWERS

ATTACH AND SECURE THE DRAWER FRONT
TO THE SLIDES

Pull out the rail assemblies to the full length
on each side of the cabinet.

Two people may be required to complete
this procedure.

STEP 8 REPLACE THE FREEZER

DRAWERS (CONT.)

Installation Instructions

Содержание Drawer Freezer Refrigerator

















Результаты поиска

Содержание Drawer Freezer Refrigerator

Отзывы:

Похожие инструкции для Drawer Freezer Refrigerator

Бренды по названию

Популярные бренды

GE Drawer Freezer Refrigerator, Руководство по установке

Результаты поиска

Содержание Drawer Freezer Refrigerator

Отзывы:

Похожие инструкции для Drawer Freezer Refrigerator

Бренды по названию

Популярные бренды