GE CARESCAPE R860 Скачать руководство пользователя

Страница: 14 / 16

To Review Patient Trends:

1.  Touch the icon to display the Past/Historical Trends
  Workspace or swipe to the right to move from the
  Present/Patient Status Workspace.
2.  From the Past/Historical Trends Workspace, choose
  any option below:
a.

Graphical Trends View: Use this view to review

historical waveforms and patient trends.
b.

Numerical Trends View: Use this view to review

patient ventilation modes and setting, measured
data, and alarm settings.
c.

Trends Log View: Use this view to review patient

alarms and settings, and events that have occurred
during ventilation.
d.

Snapshot Trends View: Use this view to save

patient data.

Pausing Ventilation

1. Disconnect the patient from the breathing circuit.
2. Select Standby.
3. Select Pause Ventilation.

Note:

Select Pause Ventilation to go into Standby.

Ventilation and monitoring will be stopped. Select Cancel
to continue ventilation if a warning message is displayed.

Содержание CARESCAPE R860

















Результаты поиска

Содержание CARESCAPE R860

Отзывы:

Похожие инструкции для CARESCAPE R860

Бренды по названию

Популярные бренды

GE CARESCAPE R860, Краткое руководство пользователя

Результаты поиска

Содержание CARESCAPE R860

Отзывы:

Похожие инструкции для CARESCAPE R860

Бренды по названию

Популярные бренды