GE AvantaPure Скачать руководство пользователя

Страница: 22 / 36

WARNING:

Only the model numbers in

Table 1 are to be used. Using a model
number that is not in Table 1 will cause
undesirable performance. If the

programmed model number needs to be changed follow
the steps below to select a valid model.

Viewing and Changing the Model

Number

Viewing the Model Number

Press and hold the SET and DOWN buttons simultaneously
until the display blanks out. Release buttons.

The Model Number will be displayed. Proceed to the next
step to change the Model Number.

Note

: The control will

revert back to the service display if no buttons are pushed
within 30 seconds

To Change The Model Number

Press and hold the SET button until 0 is displayed

Release button.

A flashing 11 will now be displayed on the screen, which is
a default model number.

Press the UP or DOWN button until the desired model
number is displayed (See Table 1). *

Press and release the SET button to save the desired model
number.

Time of day will scroll and time will be flashing.

*The Model Number setting is very important. The

AvantaPure controller software includes additional Model
Numbers that operate other AvantaPure valve types. If the
Model number is set incorrectly an

ERROR 3

could be

displayed when advancing the valve through the
regeneration cycles. The valve will not function properly.
The control Model Number must be selected from Table 1
in this service manual.

press

then

Buttons to

Press

Scrolling

Display

Description

Range

Select

MODEL

NUMBER

Time of Day

Day xx

Regeneration

Time

2. Time of Day

Set to time of day. Includes PM
monitor. The time will flash.
Default is a 12 hr clock

1. Default is 11

Must select model from table

press

then

SU, MO, TU, WE, TH, FR, SA

12 or 24

3. Day of Week

Set to actual day of the week.

4. Time of Regeneration

Set to desired time of
regeneration. The time will flash.

Full 24 hours.
Increments of 1 minute.

Programming is complete.

Avantapure 268

Service Display

Scrolling name and valve model . Time
with flashing colon.
Capacity remaining shown as 1 to 5 bars.

then

press

then

press

The range is 1-99 however,
only the model selections in
the table above are valid
selections.

Содержание AvantaPure





































Результаты поиска

Содержание AvantaPure

Отзывы:

Похожие инструкции для AvantaPure

Бренды по названию

Популярные бренды

GE AvantaPure, Руководство по эксплуатации

Результаты поиска

Содержание AvantaPure

Отзывы:

Похожие инструкции для AvantaPure

Бренды по названию

Популярные бренды