GE auisys cs2 Скачать руководство пользователя страница 208 | Manualshive

Страница: 208 / 268

background image

6.

PEEP

7.

Flow waveform

8.

TV

Figure 11-8 • SIMV PCV-VG waveforms

PSVPro mode

PSVPro is pressure supported ventilation with apnea backup.
PSVPro is a spontaneous mode of ventilation that provides a
constant support pressure once the ventilator senses that the patient
has made an inspiratory effort. In this mode, the clinician sets the
Pressure Support (Psupport) and PEEP levels. The patient
establishes the rate, inspiratory flow, and inspiratory time. The tidal
volume is determined by the pressure, lung characteristics, and
patient effort.
PSVPro uses an inspiration termination level that establishes when
the ventilator will stop the pressure-supported breath and cycle to the
expiratory phase. The inspiration termination level is user adjustable
from 5 to 75%. This parameter sets the percent of peak inspiratory
flow that the ventilator uses to end the inspiratory phase of the
breath and to cycle into the expiratory phase. If the inspiration
termination is set to 30% then the ventilator will stop inspiration when
the flow decelerates to a level equal to 30% of the measured peak
inspiratory flow. The lower the setting, the shorter the inspiratory
phase.
An apnea backup mode is provided if the patient stops breathing.
When setting this mode the clinician adjusts the inspiratory pressure
(Pinsp), respiratory rate (RR), and the inspiratory time (Tinsp). As
long as the patient is triggering the ventilator and the apnea alarm
does not activate, the patient will get pressure-supported breaths
and the ventilator will not deliver machine breaths.
If the patient stops triggering the ventilator for the set apnea delay
time, the apnea alarm will activate and the ventilator will
automatically switch to the backup mode that is SIMV PCV. Once in
this mode the ventilator will begin delivering machine pressure
controlled breaths at the inspiratory pressure level, inspiratory time,
and rate that the user has set. If, during this time, the patient takes
spontaneous breaths in between the machine breaths, the patient
will receive pressure supported breaths.
PSVPro mode settings:

•

Psupport

•

PEEP

•

Trig Window

•

Flow Trigger

•

End of Breath

•

Pmax

•

Backup Time

Aisys CS²

11-32

2067226-001

«
...
206
207
208
209
210
...
»

Содержание auisys cs2













































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для auisys cs2

Бренд: Labnet Страницы: 2

Бренд: Raytheon Страницы: 69

Бренд: Galaxy Audio Страницы: 24

Бренд: B-K lighting Страницы: 3

Бренд: Califone Страницы: 7

Бренд: CALITEK Страницы: 16

Бренд: LAHTI PRO Страницы: 20

Бренд: LAHTI PRO Страницы: 16

Бренд: J&M Страницы: 53

Бренд: Qazqa Страницы: 2

Бренд: KaVo Страницы: 49

Бренд: Easson Страницы: 33

Бренд: Taurus Страницы: 24

Бренд: IDEAL Networks Страницы: 10

Бренд: Jaga Страницы: 32

Monolith NT.115

Бренд: Nano Temper Страницы: 24

SCAFFOLDBENCH I-CISRL

Бренд: MetalTech Страницы: 16

Бренд: Salvis Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды