GE Appliances DVM1950 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 48

GE Appliances DVM1950 Скачать руководство пользователя страница 25

– 25 –

Vent Blower

The vent blower is located at the top rear of the
microwave oven. See installation instructions for
the proper method of directing the vent fan prior to
installing the unit.

To remove the vent blower:

1. Remove the oven.

(See

Microwave

Oven Removal

.)

Check to make sure the fuse is not open. Check the
noise

fi

lter for approximate resistance value at the

following locations:

White (neutral input) to white (neutral output) – 0

Ω

.

Black (line input) to black (line output) – 0

Ω

.

White (neutral input) to black (line input) – 23

Ω

.

Line Fuse

Note:

When the line fuse is blown due to operation

of the monitor switch, the monitor switch must
be replaced. Also, the relays and/or the interlock
switches must be replaced when the continuity
check shows the contacts are shorted.

The unit is equipped with a 20-amp line fuse (Part #
WB27X10928). The fuse is located on a receptacle
near the top of the noise

fi

lter board and is common

to all functions and door switches.

To remove the fuse:

1. Disconnect power to the microwave oven.

2. Remove grille assembly. (See

Grille Assembly

.)

3. Remove control panel vent plate.

4. Remove the control panel assembly.

(See

Control Panel Assembly

.)

5. Remove the fuse. (See photo below.)

High Voltage Fuse

The unit is equipped with a 20-amp high-voltage
transformer fuse (Part # WB27X10928). The fuse is
located on a receptacle near the top of the noise

fi

lter board and is common to all high voltage

functions. (See

Line Fuse

for removal procedure.)

L1 & N In

L1 & N Out

High Voltage Transformer Fuse

Line Fuse

To Power-H Relay

To High Voltage Transformer

(

Continued next page

)

Noise Filter

The noise

fi

lter helps to suppress electromagnetic

interference (EMI) radiating from the operation of
the microwave oven, and it also protects the oven
from any line noise. The noise

fi

lter is located on the

right side of the oven, behind the control panel. The
noise

fi

lter is held in place by 3 compression pins.

Note

: When installing the noise

fi

lter, ensure all

fi

lter

wiring is connected to the correct terminals.

Noise Filter

«
...
23
24
25
26
27
...
»

Содержание Appliances DVM1950

















































Отзывы:

Нет отзывов