GE AMX 4+ Скачать руководство пользователя страница 28

Страница: 28 / 36

AMX−4+ FUNCTIONAL CHECK

(MODEL 2169360, 2236420 & 2275938 SERIES)

DIRECTION 2173224−100

GE HEALTHCARE
REV 8

Repeat the above steps for each test point in Table 4: Test Points for AMX series

and record the

test results in Table 5: Results of the leakage current test under normal conditions for AMX series
for each test points.

Repeat above steps with test conditions 2 & 3 as per Table 3: Test Condition for AMX series.

AMX Series

Condition

Power

Test Meter Polarity

Normal

Table 3: Test Condition for AMX series

Test Point Components

Test Point Description

Collimator

Collimator Skin Spacers

Tube

X-ray Tube (On the HV Cable Cathode Ring)

Column

Rivets on the top column cover (Applicable only for AMX4+)

Bin

M4 Screw inserted into PEM nut on receptor bin

Tube Latch

Park Latch Assembly on the Chassis

Table 4: Test Points for AMX series

Note: Refer to Appendix 2 for the locations of the AMX series test points.

Expected Test Results

Test Point

Units Expected

Value

Measured

Value

Result

(Pass/Fail)

Collimator Skin Spacers

μA

≤ 3

X-ray Tube (On the HV Cable Cathode Ring)

μA

≤ 3

Rivets on the top column cover (Applicable

only for AMX4+)

μA

≤ 3

M4 Screw inserted into PEM nut on

receptor bin

μA

≤ 3

Park Latch Assembly on the Chassis

μA

≤ 3

Table 5: Results of the leakage current test under normal conditions for AMX series

TEST UNDER SINGLE FAULT CONDITION (SFC)

In SFC, a single fault means of protection against electrical hazard is defective or faulty.
To create Single Fault Condition, see Table 6: SFC Test conditions for 120VAC or 220VAC AC
Mains.

SFC Conditions

Condition

Power

Test Meter Polarity

X-Ray

Reversed

Earth Open

Table 6: SFC Test conditions for 120VAC or 220VAC AC Mains

To perform the Equipment Leakage Current Test under SFC, follow the steps listed below:

Note:

Refer to Table 6: SFC Test conditions for 120VAC or 220VAC AC Mains

for the test conditions

and Appendix 3: AC Power plug troubleshooting for the test equipment used. Refer to Table
4: Test Points for AMX series.

Set up test condition 1 listed in Table 6: SFC Test conditions for 120VAC or 220VAC AC Mains, follow
step 2 below.

Содержание AMX 4+





































Результаты поиска

Содержание AMX 4+

Отзывы:

Похожие инструкции для AMX 4+

Бренды по названию

Популярные бренды

GE AMX 4+, Инструкции по функциональной проверке

Результаты поиска

Содержание AMX 4+

Отзывы:

Похожие инструкции для AMX 4+

Бренды по названию

Популярные бренды