GE 750 UL S2 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 71

GE 750 UL S2 Скачать руководство пользователя страница 44

Modifications reserved

Page 44/71

OPM_SGS_USM_M75_M75_2US_V010.doc

User Manual

SG Series 750 UL S2 & SG Series 750 T12 UL S2

7 OPERATION

START UP AND COMMISSIONING

A GE GLOBAL SERVICES FIELD ENGINEER must perform start-up and

commissioning of the UPS. Please Contact GE. Global Services at least
two weeks prior to schedule start-up and commissioning at 1-800-637-
1738, or by E-mail at

This symbol refers to the operations of a parallel system.

NOTE !

Verify for correct input/output cabling before connecting

Utility

to the

UPS.
Open only the front door, do not remove any panels.

Check after every step for correct reaction of the UPS (LED’s on the
panel), and correct voltage and current measurements, before you
proceed to the next step.

NOTE !

All operations (including start-up, shutdown, removing/adding a unit
from/to a Parallel System) MUST BE PERFORMED with

eBoost™ Operation

Mode

DISABLED.

Find on the following pages the descriptions of the various procedures of start-up and
shutdown for

UPS single

and

UPS Parallel System

,

divided into the following principal

chapters:

7.1

PROCEDURES FOR SINGLE

SG Series 750

&

SG Series 750 T12

7.2 PROCEDURES

FOR

SG Series 750

&

SG Series 750 T12

PARALLEL SYSTEM

«
...
42
43
44
45
46
...
»

Содержание 750 UL S2








































































Отзывы:

Нет отзывов