background image

Tr

oubleshooting T

ips

Operating Instr

uctions

Safety Instr

uctions

Car
e and Cleaning

Installation Instr

uctions

5

Do not clean the door gasket. The door

gasket is essential for a good seal. Care

should be taken not to rub, damage or move

the gasket.

Clean only parts listed in this Owner’s

Manual.

Do not use oven cleaners. No commercial

oven cleaner or oven liner protective coating

of any kind should be used in or around any

part of the oven. Residue from oven cleaners

will damage the inside of the oven when the

self-clean cycle is used.

Before self-cleaning the oven, remove the

broiler pan, grid and other cookware.

Be sure to wipe up excess spillage before

starting the self-cleaning operation.

If the self-cleaning mode malfunctions, turn

the oven off and disconnect the power

supply. Have it serviced by a qualified

technician.

SELF-CLEANING OVEN

Use proper pan size—select cookware having flat bottoms large enough to cover the surface unit 
heating element. The use of undersized cookware will expose a portion of the surface unit to direct
contact and may result in ignition of clothing. Proper relationship of cookware to surface unit will also
improve efficiency.

Never leave the surface units unattended at

high heat settings. Boilovers cause smoking

and greasy spillovers that may catch on fire.

Do not use aluminum foil to line the drip

pans or anywhere in the oven except as

described in this manual. Misuse could result

in a shock, fire hazard or damage to the

range.

Be sure the drip pans and the vent duct are

not covered and are in place. Their absence

during cooking could damage range parts

and wiring.

Only certain types of glass, glass ⁄ceramic,

earthenware or other glazed containers are

suitable for cooktop service; others may

break because of the sudden change in

temperature. 

To minimize the possibility of burns, ignition

of flammable materials and spillage, the

handle of a container should be turned

toward the center of the range without

extending over nearby surface units.

Always turn the surface 

units off before removing cookware.

Do not immerse or soak the removable

surface units. Do not put them in a

dishwasher. Do not self-clean the surface

units in the oven.

When flaming foods are under the hood,

turn the fan off. The fan, if operating, may

spread the flame.

To avoid the possibility of a burn or electric

shock, always be certain that the controls for

all surface units are at the 

OFF

position and

all coils are cool before attempting to lift or

remove a unit.

Clean the cooktop with caution. If a wet

sponge is used to wipe spills on a hot

cooktop, be careful to avoid steam burns.

Keep an eye on foods being fried at high or

medium high heat settings.

Foods for frying should be as dry as possible.

Frost on frozen foods or moisture on fresh

foods can cause hot fat to bubble up and over

the sides of the pan.

Use little fat for effective shallow or deep fat

frying. Filling the pan too full of fat can cause

spillovers when food is added.

If a combination of oils or fats will be used in

frying, stir together before heating, or as fats

melt slowly.

Always heat fat slowly, and watch as it heats.

Use a deep fat thermometer whenever

possible to prevent overheating fat beyond

the smoking point.

SURFACE COOKING UNITS

Содержание 164D3333P072




































Отзывы: