background image

1 6

ESL 1500 Series Fire Alarm Control Panel

Troubleshooting

Table 7 provides a quick reference troubleshooting guide that will aide in diagnosing and locating most system faults quickly and
efficiently. If you cannot resolve the fault with the assistance of this guide, call Technical Support at 800.648.7424.

Table 7. Troubleshooting Guide

     Trouble indicators

Possible cause

Corrective action

End-of-line resistor value incorrect or missing

Meter circuit to verify proper resistance

Loss of power to power supervision relay

Meter voltage on circuit

Polarity reversal relay wired incorrectly

Check circuit diagram to confirm wiring

Loose connection or broken wire

Check for opens in circuit

    Zone 1-5 trouble LED

Disconnect/Walktest switch not in normal position

Put Disconnect/Walktest switch in normal position

    System trouble LED

Faulty waterflow switch

Repair or replace waterflow switch

    Trouble sounder slow

Initiating  device missing from circuit

Check for any devices that may have been removed from the

    intermittent

initiating  circuit

“Class A” wires crossed in circuit

Make sure polarity is observed completely through circuit

“Class B” wires connected to wrong terminals

Make sure wires are connected to “Class B” terminals

Incompatible two wire detector

Check UL compatibility listing to verify the detector is listed for
use with the panel

Overcurrent or lightning damage

Check for burn marks or other signs of overcurrent damage.
Return to factory for service. Replace board if traces are damaged.

     Supervisory trouble LED

Zone 2 supervisory device tripped

Check initiating device on zone 2

    Rapid trouble beep

     Zone 2 alarm LED
    Remote annunciator zone 2

    System trouble LED

Open in zone 2 circuit

Check zone 2 for broken wires or opens in circuit

    Zone 2 trouble LED

    Rapid trouble beep

Disconnect/Walktest switch not in normal position

Put Disconnect/Walktest switch in normal position

Loss of AC (line voltage)

If line voltage is too low, upgrade or move to new circuit

    Low/No AC power

Low AC power

If secondary shows less than 22 VAC replace transformer

    System trouble LED

  Less than 94 VAC at transformer primary-no load

    Trouble sounder slow

  Less than 102 VAC with maximum load

    intermittent

  Less than 22 VAC at transformer secondary-no load

Damaged transformer or loose connection

Check for loose or broken connections

Battery low

Replace batteries

    Low/No battery LED

  Less than 24 VDC

    System trouble LED

Battery missing or less than 20 VDC

Replace batteries

    Trouble sounder slow

Blown fuse

If fuse is blown, determine why fuse was blown, correct problem,

    intermittent

and replace fuse

Open in battery harness

If there is an open or break in the battery harness, replace it

    Ground fault LED

Ground on any circuit, other than alarm or trouble

Remove one wire at a time until ground fault LED and system

    System trouble LED

contacts

trouble LED goes out. Repair circuit causing fault condition.

    Trouble sounder slow

Ground in transformer

Remove AC input from board, if ground fault LED goes out,

    intermittent

there is a ground in the transformer-replace transformer

End-of-line reistor value incorrect or missing

Meter circuit to verify proper resistance

Polarity reversed in circuit

Check circuit diagram to confirm wiring and polaity

Loose connection or broken wire

Check for opens in circuit

    Indicating 1-2 trouble LED

Indicating device missing from circuit

Check for any devices that may have been removed from the

    System trouble LED

indicating  circuit

Style “Z” wires crossed in circuit

Make sure polarity is observed completely through circuit

Style “Y” wire connected to wrong terminals

Make sure wires are connected to style “Y” terminals

Overcurrent or lightning damage

Check for burn marks or other signs of overcurrent damage.

Return to factory for service. Replace board if traces are damaged.

    System trouble LED

Bad ZEM connection

Check connector pins where ZEM connects to the BMB

    Trouble sounder slow

ZEM malfunction

Check for signs of damage to the BMB or ZEM

    intermittent

BMB  malfunction

Return to factory for service or replace boards.

    (with no other indicators)

Содержание 1501





























Отзывы: