manualshive.com logo in svg

GE Interlogix 260, Руководство по установке

Поделиться
Скачать
GE Interlogix 260 Скачать руководство пользователя страница 28

24

GE Contactless Medium Read-Range Reader Model 260

The green LED 
does not light, 
but the door 
strike unlocks the 
door when a valid 
ISO 15693 or 
ISO 14443A card 
is presented.

Verify that the door strike is wired correctly. Refer 
to the appropriate wiring diagram.

Disconnect the wire from JP1 pin 7 (green LED) 
and connect JP1 pin 7 to JP1 pin 2 (ground). If the 
green LED is now on, the reader is good and the 
connection to the reader is defective. If the green 
LED does not light, replace the reader.

Green LED lights 
but the door does 
not open.

 

Verify correct door strike wiring and operation. The 
reader is functioning. If not, check that the block-
ing diode is functioning. If it is not, replace it.

Reader sounds a 
short triple beep 
every 30 seconds 
and the red LED 
flashes slowly 
(every 2 sec-
onds). 

The reader has lost communication with the micro-
controller.
Check the reader-to-microcontroller wiring, in par-
ticular, the terminations for Reader Data 1. Refer 
to the appropriate wiring diagram. Verify that the 
2RP AUX DO is jumpered to the reader data 1 on 
the microcontroller. Jumper between 2RP JP2 and 
JP4, pins 3 and 7.
Verify that the correct pull-up resistor is installed 
on the microcontroller (470 

Ω

 ½-watt, 2RP JP2 

and JP4, pins 1 and 3). 
Verify that the microcontroller has the correct firm-
ware. Refer to the manual that came with your 
microcontroller for instructions.
Try the reader on a different reader input port at 
the microcontroller. If this corrects the problem, 
the operational status of the original port is sus-
pect.
Replace the reader with one you know is working 
correctly. If this corrects the problem, then the 
reader is probably faulty and should be replaced.
If none of the above steps have identified the 
problem, there may be a significant noise source 
present in the installation which is interfering with 
the reader-to-microcontroller communications. If 
this is the case, use shielded wire for reader-to-
microcontroller connections.

Condition

Possible Solutions

Содержание 260





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды