GE HEALTHCARE AKTAprime plus Скачать руководство пользователя страница 3

Страница: 3 / 40

11-0027-48 AC, 2007-09 • p3

e) Place the tubing holder over the length guide (small

hole) in the delivery arm, push the tubing down to the
bottom of the guide and tighten the nut. This ensures
that the correct length of the tubing is exposed.

Note: Make sure that the end of the tubing is cut
leaving a straight edge. For more information, see

ÄKTAprime plus User Manual

Set Drop Sync Active

(yes)

Set Parameters

f) Re-install the tubing holder

into the delivery arm.

g) Rotate the rack by hand until the rear half of the tube

sensor rests against tube 1.

h) Press

feed tube

on the front panel. The bowl moves to

the correct position to collect the first fraction in tube

i) Make sure that drop synchronization is activated.

Note:

Drop synchronization can only be used at flow

rates

≤

3 ml/min.

Cleaning the sample loop and

connecting the column

a) Mount a sample loop between port 2 and port 6 that

is large enough to hold your sample.

Clean the loop and the injector fill port:

Inject (with a syringe) 5 times the loop volume of water

or binding buffer through the injection fill port.

c) Connect the column between port 1 on the injection

valve (7-port valve) and the UV flow cell.

Filling the buffer inlet tubing

Prepare the buffers. Make sure that correct inlet tubing is
put into correct buffer.
•

If using an application template:

It is not necessary to perform the wash procedure
because this is included in the method.

•

If using a method template:

Pre-fill all inlet tubings with buffer. Select the

application template

System Wash Method

, select

the inlets to be washed and press

The system is now prepared. Start the method.

Storage of the system

Clean the loop and the injector fill port:

• Inject (with a syringe) 5 times the loop volume of

water through the injection fill port.

• Repeat this step with 20% ethanol.

Flush the system flow paths:

• Put all used inlet tubings in water.
• Select the application template

System Wash

Method,

select the inlets to be washed and press

• For long-term storage of the system, repeat

step b) with 20% ethanol.

c) Shut down the system.

Tubing holder

HiTrap

1/16" Male

UV monitor

1/16" Male

HiPrep

Содержание AKTAprime plus









































Результаты поиска

Содержание AKTAprime plus

Отзывы:

Похожие инструкции для AKTAprime plus

Бренды по названию

Популярные бренды

GE HEALTHCARE AKTAprime plus, Краткое руководство по эксплуатации

Результаты поиска

Содержание AKTAprime plus

Отзывы:

Похожие инструкции для AKTAprime plus

Бренды по названию

Популярные бренды