background image

Page 6-1

SPIRE II Series

 – Installation and Operating Instructions

6. o

peratIon

s

equence

 

oF

 o

peratIon

Mode

Photo Safety Sensor  
Clear and No Micro 
Switches activated

Safety Eye Blocked

Micro-Switch 
Activated

Emergency Stop 
Switch Pressed

RUN

When 

RUN

 is pressed, 

the rollers rotate at the 
set speed.

When the Photo Safety 
Sensor is blocked, the 
rollers do not rotate 
when 

RUN

 is pressed. 

When the Micro-
Switcha is activated, 
the rollers do not rotate 
when 

RUN

 is pressed.

When 

RUN

 is pressed, 

the rollers do not rotate.

When 
machine 
is running

The rollers will rotate at 
the set speed.

When the Photo Safety 
Sensor is blocked when 
the machine is running, 
the rollers stop.

When the Micro-
Switcha is activated 
while the machine is 
running, the rollers stop.

When Emergency 
Stop (also referred to 
as E-Stop) Switch is 
pressed while running, 
the rollers stop.

Footswitch 
is pressed

When the Footswitch 
is pressed  the rollers 
rotate at the set speed.

When the Footswitch 
is pressed , the rollers 
rotate at 3 ft. (1 meter) 
per min.

When the Footswitch 
is pressed , the rollers 
rotate at 3 ft. (1 meter) 
per min. when you 
press the Footswitch.

When the Footswitch is 
pressed the rollers do 
not rotate.

When the Footswitch 
is released, the rollers 
stop rotating unless 

RUN

 is pressed and the 

Footswitch is released.

Once the Photo Safety 
Sensor is clear, 

RUN

 

is pressed, and the 
Footswitch is released, 
the rollers rotate at 
the set speed without 
stopping.

When the Footswitch is 
released, the rollers will 
stop rotating.

REV 
(Reverse

When 

REV

 is pressed 

and held, the rollers 
rotate in reverse at 3 ft. 
(1 meter) per min.

When 

REV

 is pressed 

and held, the rollers 
rotate in reverse at 3 ft. 
(1 meter) per min.

When 

REV

 is pressed 

and held, the rollers 
rotate in reverse at 3 ft. 
(1 meter) per min.

When 

REV

 is pressed 

and held, the rollers do 
not rotate.

When REV is released, the rollers stop rotating.

a.  An internal Micro-Switch is activated when the Feed Table is removed.

Содержание 54C













































Отзывы: