background image

10. 

Inspection, maintenance and repair

   Warning!

 Disconnect the product from mains before performing any 

maintenance or repairs. 

   Warning!

 Do not disconnect the Wieland RST20i3 plug under load. 

   Warning!

 Do not open or disassemble the fixture, it contains no servicable parts 

inside. Opening the fixture can be dangerous and will void the warranty. 

   Warning!

 Always allow for a cool down period of at least 30 minutes before 

touching the lamp or reflector.

   Caution!

 Do not clean the fixture with detergents, abrasives or other agressive 

substances. 

   Caution!

 Do not touch the inside of the reflector during installation.

   Caution!

 Wait 20 minutes before activating the fixture after maintenance work 

has been conducted.

 

 Note: 

Gavita recommends to measure the lamp and reflector for aging every 

year. Replace the lamp and/or reflector when they are aged.

• 

Regularly check the fixture for dust or dirt buildup. Clean if necessary. 

Contamination may couse overheating and decreased performance.

 

-

Clean the inside of the reflector with soapy water, but use demineralised 

water to rinse the reflector;

 

-

Clean the electronic ballast and the outside of the fixture using a dry or damp 

cloth.

• 

Check the lamp monthly for discolorations or black markings. Always replace a 

damaged lamp.

 

 Note: 

Before initial use, the lamp could have black markings. This will disappear 

when the lamp runs on full power. If not, replace the lamp.

• 

Regularly check the wiring of the product to ensure it is undamaged.

10.1. 

Placement and replacement of the lamp

   Caution!

 Do not touch the lamp with bare hands as this will damage the lamp. 

Always use a fabric glove to handle the lamp. 

   Caution!

 Only use lamps specified by Gavita (see paragraph 3.3).

 

 Note: 

Gavita recommends replacing the lamp after 10000 lighting hours. 

• 

Switch off mains power.

• 

Use a fabric glove to carefully unscrew the lamp from the socket (6). Use a protective glove if the lamp is damaged.

• 

Use a fabric glove to carefully screw a new lamp into the socket (7).

• 

Switch on mains power.

1

2

1

2

6. 

1

2

1

2

7. 

Содержание GAN Electronic 600 W 230 V EU









Отзывы: