manualshive.com logo in svg

Gaumard S405.100, Руководство пользователя

Поделиться
Скачать
Gaumard S405.100 Скачать руководство пользователя страница 53

S405.100 & S406.100 

| 

USER GUIDE

Troubleshooting | 53

6. TROUBLESHOOTING

6.1 GENERAL TROUBLESHOOTING

Symptom

Possible Cause

Solution

Control box not circulating blood 
dispensing bag fluid

Power is not being delivered to the 
control box

Check that the port on the 
control box that the power 
cable plugs into is not 
damaged. Remove the power 
cable from the control box and 
inspect the port. The metal pin 
inside the port should not be 
damaged or bent in any way. 

Disconnect and firmly reconnect 
the power cable that plugs into 
the port on the control box. It 
may be that the power cable 
was not properly connected. 

Check that the outlet the 
power cable is plugged 
into is a working one. 

There is no fluid flowing through 
the vasculature of the arm when 
the system is turned ON; no fluid is 
exiting the drainage tubings. 

The fluid flow is restricted

Ensure that all of the tubing is 
unclamped. 

Disconnect and clean the 
system. It is possible that 
leftover artificial blood 
concentrate in the system 
clogged the vasculature. 
Reconnect the system and try 
again.

Roll down the arm skin and 
inspect the veins. Ensure that 
the veins are not kinked. Tape 
down veins to keep them in 
place if necessary. Replace veins 
as needed. 

The arm is leaking from the puncture 
marks on the arm skin

The arm skin and/or veins have been 
punctured with too large a needle or 
too many times

Replace the arm skin and veins 
as needed. Refer to section "5. 
Routine Maintenance" on page 
38

Содержание S405.100































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды