GAUI X5, Руководство по сборке

Страница: 5 / 26

P.1
#A #B #C #D #E
#F
#G #H
#I #J
1 2 3 4 5
6 7 8 9 10
每一個插圖中的代號(#A,#B,#C…1,2,3…)僅代表該插圖中的某一零件，
同一插圖中若有相同尺寸之零件，會以相同代號代表，插圖代號僅供組裝參考用。
以上圖示，於組裝時請確實注意，避免組裝後試飛造成失控零件鬆脫等情況發生。
Code Letter/Number (#A,#B,#C…,1,2,3…) used in each figure indicates the
specific part in that figure only, please refer to the parts list for the
actual item numbers. Code Letter/Number is only for the reference in assembly.
Make sure to assemble the parts as shown in figure above, incomplete/
incorrect assembly may cause the control failure during flight.
B-Bearing
B-軸承
Ø-Tap Screw
Ø
-粗牙螺絲
M-Machine Screw
M-公制螺絲
P-tube
P-柱狀體
Pillar
P-柱狀體
N-Nut
N-螺母
W-Washer
W-華司
B(內徑)X(外徑)X(厚度)
Ø
(外徑)X(長度)
M(外徑)X(長度)
P(內徑)X(外徑)X(長度)
P(外徑)X(長度)X(實心柱)
N(外徑)X(長度)
W(內徑)X(外徑)X(厚度)
Mark
類別
indication
標示
(mm)
B(Dia.in)x(Dia.out)x(Thickness)
Ø(Dia.out)x(Length)
M(Dia.out)x(Length)
P(Dia.in)x(Dia.out)x(Length)
P(Dia.out)x(Length)
N(Dia.in)x(Width) L-Lock nut
W(Dia.in)xDia.out)x(Thickness)
組裝代號說明
Figures instruction
規格資料
Specification
螺絲止鬆劑 上膠位置約為螺紋前端1mm寬度。
Use the thread-lock adhesive if the screws are
tightened to the metal parts.
組裝時如遇螺絲鎖於金屬件，請適量使用 螺絲止鬆劑
以確保飛行安全!
Use the thread-lock adhesive on the
tip of screw for 1mm width.
Gear Ratios 齒輪傳動比: 7.5 : 1 : 4.07 (E.M.T)
Main rotor speed 2693 rpm Tail rotor speed 10960 rpm
Overall Length (with Canopy):1
000Specifications
機身長度(含艙罩):1000 mm
Flybar Paddle:64x40x5mm
平衡翼尺寸:64x40x5 mm
Main Rotor Diameter:1120mm
主旋翼迴轉直徑:1120 mm
Main rotor blades:500 ~ 530mm
主旋翼長度:500 ~ 530mm
Overall Height:343mm
機身高度:343 mm
Overall Width:165mm
機身寬度:165 mm
Tail Blade Length:82mm
尾旋翼葉片長度:82 mm
Tail Rotor Diameter:235mm
尾旋翼迴轉直徑:235 mm
Flying duration: 4 ~ 5 minutes with
飛行時間: 4 ~ 5分鐘
Power System(Recommanded):
Motor -- 910KV
ESC 100A ESC
6S1P(22.2v/4200mah)
動力系統(原廠建議):
馬達 910KV
電子變速器 100A ESC
使用鋰聚電池:6S1P(22.2v / 4200mah)
Total weight: 1900g ±3% (Equipped with Blades and
all electronic gears except Battery).
全配重量:1900g ±3% (全套含電子裝備不含電池)
Gear Ratios 齒輪傳動比列表 Standard Equipment 標準配備
13T Steel Pinion Gear (E.M.T) 9.2 : 1 : 4.07 = 2195 rpm
208786 - X5 Steel Pinion Gear Pack (16T- for 5.0mm shaft)
X5 鋼製馬達齒16T(孔徑5.0mm)
14T Steel Pinion Gear (E.M.T) 8.6 : 1 : 4.07 = 2349 rpm
208903 - 61T Gear (Set of 2)
61T齒輪(2件組)
15T Steel Pinion Gear (E.M.T) 8 : 1 : 4.07 = 2525 rpm
208381 -
Front drive gear set and Pulley Shaft with Steel Gear (15T)
尾傳動導輪軸(15T)附傘齒組
16T Steel Pinion Gear (E.M.T) 7.5 : 1 : 4.07 = 2693 rpm
208601 - (GUEC GM-601)Brushless Motor(1820W-910kv)
(GUEC GM-601)無刷馬達(1820W-910kv)
Tail Speed
: 10960 rpm
208901 - 120T Main Gears
120T主齒盤
注 意:更改動力系統請注意電池電壓，馬達KV值及減速比 的關係來做搭配。
Improtant : The gear ratio, motor and battery should be setproperly if the power system changed!!