GAUI NX4, Инструкция по эксплуатации

Страница: 6 / 38

GAUI
TAI SHIH HOBBY CORPORATION
Tools and Equipment for Assembly
自備工具及設備
2.0mm Hexagon screwdriver 3.0mm Hexagon screwdriver 2.5mm Hexagon screwdriver 3.5mm Hexagon screwdriver
2.0mm 六角螺絲起子 3.0mm 六角螺絲起子 2.5mm 六角螺絲起子 3.5mm 六角螺絲起子
Needle-nosed pliers Diagonal cutting plier Ball Link Plier Phillips screwdriver
尖嘴鉗 斜口鉗 拔豆鉗 十字螺絲起子
Scissors Governor FBL system
Transmitter & Receiver (6 c)
剪刀 引擎定速器組 陀螺儀 六動以上接收機&發射機
CCPM Servo x3pcs Tail Specialized Servo x1pc CA
CCPM伺服機x3個 尾舵伺服機x1個
Throttle Servo x 1pc
油門伺服機x1個 瞬間膠
General thread lock
Anaerobic adhesive Lubricant / one-way bearing grease
AB glue
螺絲止鬆劑 特殊型缺氧膠 潤滑油 / 單向軸承油 AB黏著劑
A B
Battery 2S 7.4v 800~1500mAh Glow starter
Engine Starter
Fuel pump
鋰聚電池2S 7.4v 800~1500mAh 點火器 啟動器 加油器
危 險: 組裝過程中請小心安裝並注意
此危險程度可能造成安全性漏洞
導致人為傷害。
一般型止鬆劑
鎖緊螺絲並確認上膠
使用瞬間黏著劑
一般型止鬆劑
務必鎖緊螺絲並確認上膠
Apply general thread lock.
Tighten screw and apply thread lock.
Danger: High level of attention must be
taken during assembly.
Action during assembly might be hazardous.
Extreme care should be taken to avoid injury.
Apply general thread lock.
Be certain to tighten screw and
apply thread lock.
Apply anaerobic adhesive.
Be certain to tighten screw and
apply thread lock.
Apply CA glue Apply lubricant
Apply anaerobic adhesive. Apply general thread lock.
特殊型缺氧膠
務必鎖緊螺絲並確認上膠
依個人需求使用潤滑油。
Pillar
P-柱狀體
P(Dia.out)x(Length)
P(外徑)X(長度)X(實心柱)
N-Nut
N-螺母
N(
Dia.out
)x(Width) L-Lock nut
N(外徑)X(長度)
W-Washer
W-
華司
W(Dia
.in
)xDia.out)x(Thickness)
W(內徑)X(外徑)X(厚度)
P-tube
P-柱狀體
P(Dia.in)x(Dia.out)x(Length)
P(內徑)X(外徑)X(長度)
B-Bearing
B- 軸承
B(Dia.in)x(Dia.out)x(Thickness)
B(內徑)X(外徑)X(厚度)
Ø-TapScrew
Ø-
粗牙螺絲
Ø(Dia.out)x(Length)
Ø(外徑)X(長度)
M-Machine Screw
M-公制螺絲
M(Dia.out)x(Length)
M(外徑)X(長度)
使用特殊型缺氧膠。 一般型止鬆劑
以上圖示，於組裝時請確實注意，避免組裝後試飛造成失控零件鬆脫等情況發生。
Make sure to assemble the parts as shown in figure above. Incomplete or incorrect assembly may
cause control failure during flight.
使用AB黏著劑
Apply AB glue