Gateway E-4400 Скачать руководство пользователя

Страница: 110 / 118

Specifications

105

Specifications

The following specifications are for the standard configuration; your system
may contain optional equipment. All specifications are subject to change.

Case size (without the optional
minitower base)

Width: 15" Depth: 17.5" Height: 4.7"

Processors

Intel

Pentium III™ processors operating

at 533, 600, 733, 800, 866, 933 MHz and
faster

Cache

256k or 512K, depending on processor

RAM

Two RIMM sockets on the system board
support 2.5 volt Rambus Dynamic
Random Access Memory (RDRAM)
RIMMs. Maximum memory is 1 GB

BIOS

Flash BIOS for easy updates from diskette

Video

4X AGP slot

IDE interfaces

Supports up to two ATAPI/IDE devices
(hard drives or CD drives) using two
onboard PCI IDE controllers

Diskette drive interface

A diskette drive controller is integrated on
the system board

Содержание E-4400























































































































Результаты поиска

Содержание E-4400

Отзывы:

Похожие инструкции для E-4400

Бренды по названию

Популярные бренды

Gateway E-4400, Системное руководство

Результаты поиска

Содержание E-4400

Отзывы:

Похожие инструкции для E-4400

Бренды по названию

Популярные бренды