background image

CX700 / CX560 Operation 

Page 21 

 

 

Using the GP3A2 Wide Angle Port 

 

 

Super Range image stabilization. 

 With the CX700 / CX560 camera only, you may 

find momentary vignetting occurs with swift movements left or right when using 
Super Range image stabilization.  If so, make smooth pans to either side, or change 
the image stabilization to Standard mode.  

 

Photo Mode.

  Due to variations in cameras you may find very slight vignetting in 

Photo Mode and at highest picture size (L 3264 x 2456).  To avoid this, it may be 
necessary to zoom ~ 2% from full wide. One momentary action on the zoom control 
toward telephoto is sufficient.

 

Cleaning Ports and Filters 

Gates ports can be cleaned readily by following these simple guidelines. 

 

Dust or Lint 

can be blown with compressed air, preferably from a can.  Do not 

clean the surfaces if it is unnecessary.

  

 

Salt deposits or sand may also be removed with compressed air.  

Use a soft 

lens brush if necessary to brush away foreign material that remains.

 

 

Rinse fresh water over the outside of the port, if necessary,  

to loosen any 

residual salt or sand that may remain.  Do this with the port sealed on your housing 
to keep water away from the rear of the port.  

 

 CAUTION

Do not submerge the GP32A wide angle port in water when separated 

from the housing!  This port is not sealed from the backside and damage will result if 
submerged.

  

 

 

Only if necessary,

 clean the port using a mild cleaning solution and a non-

abrasive, lint free cloth.  

Use light circular strokes when wiping away cleaning 

solution and any foreign material.   Excessive pressure used when cleaning dirty 
lenses (e.g., rubbing sand into the lens surfaces) may damage coatings. Use a light 
touch.

 

 CAUTION

Not all cloths are lint free and non-abrasive!  Use of an abrasive material 

(such as cotton balls and cotton fabric) may scratch the glass and/or coating of 
Gates ports and will void the warranty.

   

 

TIP

:   Gates offers approved cleaning solutions and lint free cloths as accessory 

items.   Use of these materials will not void your warranty.   

Содержание CX560


























Отзывы: