background image

PAGE 6

G427

INSTRUCTION MANUAL

INSTALLATION

Installing the camera....cont

1.   Connect the RED wire of the Cameras Power Harness to the wire that supplies power to the 

reversing light globe (the wire that is energized only when the car is put into reverse). Before making 

the electrical connection, temporarily disconnect the camera from the power plug whilst making the 

connection to the reversing light globe. Use a suitable splicing/crimp connector (scotch lock type) or 

strip connector. This connection can also be soldered, making sure to insulate the joint with electrical 

insulation when done. The camera has only one wire to connect (positive (+). There is no need to 

hook up a ground earth wire as the camera gets its earth through the RCA cable. Hooking up the 

ground earth may cause a ground loop. In this case horizontal lines will appear in the image.

2.   After you have insulated the join you can connect the power harness to the camera.

NOTE:

Some cars that run LED or computer controlled lighting systems may not deliver enough

voltage to run the camera. If the voltage at the reversing wire light is less than +12 volts it may be 

necessary to use a relay to supply power to the transmitter harness from the wiring in the front of 

the car.  In this case the reversing light only needs to trigger the relay. Make sure that you do not 

drill holes in the panels that have an opposite face that is visible outside the car for example guard 

panels. In fact, whenever drilling holes in the bodywork of a vehicle, always see what is on the other 

side.

3.   Connect one end of the supplied RCA cable to the RCA socket from the camera, then run the 

RCA cable to the front under side of the driver side dash board. This is where the monitor’s loom will 

be located. To do this you will need to remove the rear seat to pass the cable into the cabin area and 

you will need to remove the door scuff plates to run the wire along the side of the vehicle. The RCA 

cable will be hidden when you replace the scuff plates. When the cable is at the front of the vehicle 

the RCA cable needs to be run from the scuff plate area to the underside of the dash behind the kick 

trim (remove and run cable).

4. The monitor has two power wires to be connected. Connect the red wire (acces12V) to a 

wire that is energized when the vehicles accessories is turned on. 

Connect the black wire to a ground earth wire or to the body of the car using the steel of the cars 

body behind the kick trim as an earth. In this case drill a small hole and connect the wire using a 

suitable ring terminal. Scrape off the cars paint around the hole to ensure good earth.

5. Connect the RCA cable to the RCA socket from the monitors loom.

Testing the reverse camera function

1.Engage the park brake and turn the ignition key to the on position. DO NOT start the vehicle.

2. Select reverse gear with the gear shift. The monitor will sense the video signal from the camera 

automatically and will display the camera’s image of the rear of the vehicle.

Содержание G427









Отзывы: