EN
EN
110
111
REMOVING OBSTACLES
WARNING
– Do not pour any type of liquid into the feed chute of the mincer,
while the mincer is assembled to the mixing arm. Do not insert any foreign objects
into the feed chute (e.g. cooking utensils). Do not remove the screw ring from the
mincer housing with the mincer assembled to the mixing arm and the machine con-
nected to the power supply.
CAUTION
– Immediately switch off the motor (press the control dial), when the
motor keeps running noticeably slowly or gets blocked. This may avoid overloading
or overheating the motor and thus maintain long-lasting high performance of the motor.
When processing tough pieces of food (e.g. tendons or gristle within meat) or dough
with pieces of nuts, fruit, or hard vegetables and similar ingredients, the mincer may
be clogged. Large, hard pieces (e.g. bones) could block the worm shaft and/or
cross blade. In the extreme case, the mincer could get damaged (see: ‘Tips for Best
Results / Using the Mincer’).
1. Press the control dial for switching off the motor and unplug the machine.
2. Remove the tablet of the mincer. Then, remove the mincer from the mixing arm
and turn off the screw ring from the mincer housing (see: ‘After Usage / Remo-
ving and Disassembling the Mincer’).
3. With single hard pieces clogging the outlet of the mincer, it may be sufficient to
pull out the mincing disc, clean the holes of the mincing disc, and remove the
blockage from the cross blade. Check, whether the worm shaft can be turned
freely within the mincer housing. With the worm shaft blocked (you cannot turn
it manually after removing the screw ring), you must disassemble the mincer com-
pletely (see: ‘After Usage’). Possibly, you need to press the worm shaft and used
tools out of the mincer by pressing on the hexagonal shaft of the worm shaft.
4. Remove the obstacle and check, if the parts of the mincer are undamaged.
Damaged parts must be replaced. Ensure that the openings of the used tools are
free from obstacles.
5. Re-assemble the mincer according to the instructions for the individual tools (see
above).
IMPORTANT -
Ensure that the hexagonal shaft of the worm shaft and the coupling
side of the mincer are completely clean and dry, before re-assembling the mincer
to the mixing arm of the machine. Otherwise the mincer coupling of the mixing
arm could be polluted or even get damaged.
6. If required, clean and dry the hexagonal shaft and the coupling side of the mincer.
7. Re-assemble the mincer at the mixing arm of the machine (see above). Ensure that the
motor of the machine is operating as usual, before processing further pieces of food.
NOTE
For further information refer to the chapter ‘Solving Problems’.
OPERATING TIME AND PAUSE FUNCTION
For your convenience, the machine offers an operating timer and pause function.
These features are described in this section.
ADJUSTING THE OPERATING TIME
You can set a pre-defined operating time. When starting motor operation, the set
operating time is counted down to zero and the operating time still required for com-
pleting the mixing process is shown on the operating time display.
When switching on the machine, the operating time starts always with the default
(20 minutes, “20:00”).
When turning the control dial back to zero speed (“00”), the operating time is set to
the default (20 minutes). If you wish to interrupt operation without resetting the timer,
use the pause function (see below: ‘Using the Pause Function’).
You can cancel operation at any time you like by turning the control dial to zero or
switching off the machine (pressing the control dial for approx. 2 seconds).
1. Press the up/down arrows at the left side of the operating time display for setting
the operating time. You may operate the machine using any value between 30
seconds (“00:30”) and 20 minutes (“20:00”) in steps of 30 seconds.
NOTE
Hold the appropriate arrow pressed, for scrolling through the timer setting auto-
matically.
2. After setting the operating time, turn the control dial clockwise for selecting the
desired speed and starting operation. The timer starts immediately and the ope-
rating time is counted down. When the timer reaches zero (“00:00”), the motor
is turned off automatically and zero flashes on the speed display (“00”). The
operating time is reset to the default value (20 minutes).
3. If you wish to cancel operation and/or set the operating time back to the default
value (“20:00”), simply turn the control dial back to zero (“00”) manually.
