20
21
ling level is above the MIN indicator (“500 ml/MIN”). However, do not overfill
the kettle.
Observe the maximum filling level depending on the intended task.
• Heating water: 1.5 litres (“1500 ml/Water MAX”);
• Preparing tea: 1.2 litres (“1200 ml/Tea MAX”);
• Using the glass insert: 1.1 litres (1100 ml).
Important:
Always keep the kettle level, as soon as it is filled. When filling the
kettle, ensure not to spill water on the exterior of the kettle. If required, wipe dry
the exterior of the kettle, before placing the kettle onto the power base.
4. Ensure that the exterior of the kettle is dry. Then place the kettle onto the power
base and connect the appliance to the power supply. A beep will sound and
the display will get illuminated. The first tea program (“Green”) will be selected
and the set temperature of this program will be shown on the display. The appli-
ance is now ready for operation (Standby mode).
Note
You may cancel any operating cycle at any time via holding the “Start/Stop” but-
ton pressed for approx. 3 seconds until a signal sounds. The appliance will switch
back to standby mode.
If the appliance is idle for more than 5 minutes, the kettle will shut off and the dis-
play will get dark. Press any button, if you wish to switch on the appliance.To red-
uce energy consumption, it is good advice to avoid leaving the appliance in keep
warm mode uselessly.
BRINGING WATER TO THE BOIL
Prepare the appliance for operation (see above: ‘Preparing the Appliance for Ope-
ration’) filling the kettle with the desired amount of water from 0.5 litres (“500ml/
MIN”) to 1.5 litres (“1500 ml/Water MAX”).
1. Close the kettle using the tea lid set (see: ‘Knowing Your New Tea & More’).
Push the tea lid ring down on the kettle until it settles firmly. Then, holding the
tea lid by the handle, insert the tea lid in the tea lid ring with the white arrow
pointing to “Open”. Turn the tea lid clockwise within the tea lid ring to “Close”
for locking the tea lid securely.
Important:
Do not operate the kettle with the lid open. Otherwise, the tempera-
ture control and automatic shut-off will not work properly. Additionally, there will
be high energy loss. It is crucial, that the tea lid set is installed firmly on the kettle.
Otherwise the lid set could fall down during pouring.
2. Press the “Hot water/Cooking” button to select the “Hot water” program. “100°C”
will be shown on the display. With this program you cannot make any further entries.
3. Shortly press the “Start/Stop” button to start the boiling cycle. The kettle starts
heating immediately. On the display, two dashes are shown first. As soon as the
water in the kettle reaches 30°C the actual water temperature is shown. With
the water at boiling temperature (100°C), the appliance switches off the heating
plate and, with an acoustic signal, goes back to standby mode immediately.
4. Remove the kettle from the power base and carefully pour the water. With the
tea lid set installed correctly, the lid set will not fall during pouring. Ensure not to
spill the hot water to avoid injuries and damage.
MAKING TEA
You may make your tea directly within the kettle. You will need the tea lid ring (with
small opening), the small tea lid, and, when using tea leaves or dried fruits without
a tea bag, the tea filter.
1. Prepare the appliance for operation (see above: ‘Preparing the Appliance for
Operation’). For this, fill the kettle with the desired amount of water between 0.5
litres (“500 ml/MIN”) and 1.2 litres (“1200 ml/Tea MAX”). Do not overfilling
the kettle, to avoid overflow, when the water is boiling or the ingredients for your
tea are swelling up.
2. Fill the tea filter with the ingredients for your tea.
3. Place the tea lid ring on top of the kettle and press it down to fix it. Close the
opening in the lid ring with the tea lid.
4. Select the desired tea program by pressing the “Tea” button several times until
the desired program is indicated on the top line of the display (see: ‘Tea Pro-
grams’). The pre-set temperature for each tea program is shown on the display.
Note
With the tea program “Ice”, only the steeping time can be set.
5. If you wish to change the temperature, turn the “°C/Time” knob, until the desired
temperature is displayed. Temperature values from 40°C to 100°C (boiling) are
possible.
6. If you wish to change the steeping time, press the “°C/Time” button for switching
to time display. Turn the “°C/Time” knob, until the desired time is shown. Time
values from 30 seconds (0m30s) to 10 minutes (10m00s) are possible. Using the
“°C/Time” button, you can switch between time and temperature as you like.
