manualshive.com logo in svg

GasTech F-GUARD IR3-HD, Руководство пользователя

Поделиться
Скачать
GasTech F-GUARD IR3-HD Скачать руководство пользователя страница 14

For more information & technical support: [email protected]

9

76-M-6010-02-02

 

F-Guard IR3 HD User Manual

Environment 

•

Environmental conditions including but not limited to dust, snow or rain can

reduce the detector's sensitivity and require additional consideration.

Hot Work 

•

Arc welding should not be performed within 12 ft. (3.5m) of the detector. It is

recommended that the system be inhibited during welding operations in

situations where the possibility of a false alarm cannot be tolerated.

•

Gas welding requires a system inhibit since the gas torch is an actual fire.

•

Arc welding rods can contain organic binder materials in the flux that burn during

the welding operation and are detectable by the device.

•

Welding rods with clay binders do not burn and should not be detected. However,

a system inhibit is always recommended, since the material being welded may

be contaminated with organic substances (paint, oil, etc.) that will burn and may

be of the size that should be detected.

Содержание F-GUARD IR3-HD














































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды