5
4
GENERAL ASSEMBLY
Connecting & Disconnecting to the Gas Source
Familiarise yourself with the general information and
safety guidelines located at the front of this manual.
DO NOT USE AN ADAPTOR ON THE CYLINDER
CONNECTION
Check
1. The cylinder is filled. A sloshing sound will be heard
when shaken.
2. The burner controls are in the ‘OFF’ position
Connecting
1. Ensure cylinder valve is in its full off position.
2. Check for any damage to either the cylinder
connection or the hose. NEVER attempt to use
damaged equipment.
3. When connecting the hose to the cylinder tighten the
nut to a positive stop by hand.
4. Open cylinder valve fully. If a leak can be heard at
either end of the hose turn cylinder off and tighten
joint. Wait 5 minutes before re-testing and use a
soapy water solution to check the joint. If bubbles
appear the connection will need to be re-tightened.
Disconnecting
1. Ensure the burner control is in the ‘OFF’ position.
2. Ensure cylinder valve is in the full off position.
For storage and cylinder exchange, disconnect hose
at the cylinder only, DO NOT disconnect hose from
appliance.
Disconnecting
1. Ensure the burner control is in the ‘OFF’ position.
2. Ensure cylinder valve is in the full off position.
FOR STORAGE AND CYLINDER EXCHANGE,
DISCONNECT HOSE AT THE CYLINDER ONLY, DO
NOT DISCONNECT HOSE FROM APPLIANCE.
REMOVE TRANSIT PACKAGING MATERIAL
BEFORE USE.
Burner Operation & Ignition System Check
1. Open the Lid of the barbecue before attempting to
light the burner.
2. Turn the control knobs clockwise to “OFF” position.
3. Connect the regulator to the gas bottle. Turn the gas
supply “ON” at the cylinder. Check with the use of
soapy water for any gas leakage between the bottle
and the regulator.
4. Push down a control knob and keep pressing whilst
turning anti-clockwise to the “HIGH” position (a
clicking sound is heard). Continue to hold the control
knob for 10 seconds (This is to ensure the Flame
Failure Device to be engaged). Release then check
the flame stays on.
5. If the burner still does not light, turn the control
knob to ‘OFF’ wait 5 minutes and repeat the lighting
procedure.
6. Adjust the heat by turning the knob to the High/Low
position.
7. To turn the barbecue ‘OFF’, turn the cylinder valve to
the ‘OFF’ position and then turn the control knob on
the appliance clockwise to the ‘OFF’ position.
Problem
Possible Reason
Solution
Burner will not ignite
Valve on cylinder is closed
Open valve on cylinder
Control knob is off
Turn knob to high when lighting
Ignition system not working
Check battery - The control knob should have a
clicking sound when pressed
Burner has gone out
Check that the gas bottle is not empty
Igniter is faulty
Use a long barbecue match
Flame not staying on
once control knob is
released
Control knob not held down long
enough for Flame Failure Device to
engage
Repeat the lighting procedure and hold control
knob down for 15 seconds
IMPORTANT
• Do not smoke when attempting to ignite the
barbecue.
• Never use volcanic rock, heat beads or other
material.
• Always use protective gloves when handling hot
components.
• Note: If for some reason, ignitor fails to produce
a spark at the electrode, barbecue can be lit by a
long barbecue match. With the cover removed, lift
out the grill plate and light a burner with a match or
lighter. Subsequent burners will crosslight.
• The lid must be in the open position for lighting and
during use.
• Do not leave the barbecue unattended when alight.
• Clean your barbecue after each USE. DO NOT use
abrasive or flammable cleaners, as it will damage
the parts of the product and may start a fire. Clean
in warm soapy water.
• IMPORTANT: Before connecting and disconnecting
barbecue to gas source, make sure burner controls
are in ‘OFF’ position.
• CAUTION: When the barbecue is not in use, the gas
must be turned off at the cylinder
• Check that the seals between the appliance and
the gas cylinder are in place and in good condition
before connecting the gas cylinder
• Do not use this appliance if it has damaged or worn
seals.
• Check performance of burner prior to installing BBQ
plates.
Nominal Hourly Gas Consumption
Model No.
Gas Type
Number of Burners
Injector Size
Side Burner
Total Gas
Consumption
MJ/h
Gas Pressure kPa
BQ2027
BQ2027BL
ULPG
1
Ø 1.32mm
23 MJ/h
2.75 kPa
MJ/h Each
23 MJ/h
BQ2027NG
BQ2027BLNG
Natural
Gas
1
Ø 2.36mm
21 MJ/h
1.0 kPa
MJ/h Each
21 MJ/h
S.G.A. Pty Ltd. 33-35 Lionel Road, Mt. Waverley,
Victoria 3149, Australia.
FOR CORRECT OPERATION REFER TO INSTRUCTIONS PROVIDED.
A.G.A
Approval No.
AGA 8250 G
AGA 9117 G
LCC27 Regulator
& Hose
LCC27 Gas
Cylinder
(Cylinder
Not Included)
LCC27 Cylinder
Connection Device
LIGHTING PROCEDURE
Install and replace battery
The BBQ is featured with electronic ignitions system,
which is powered by one AA battery.
To install or replace a battery, rotate to remove the
battery cover. Insert a new battery as below image
shows, then replace the battery cover.
NOTE: Ensure the battery has been placed in the correct
orientation as shown.
