background image

7

6

ASSEMBLY INSTRUCTIONS

Your fire table must be installed on flat, stable 
surface, away from any combustible materials or 
construction.

Make sure the appliance control knob is turned 
“off” before assembling.

Note: Remove any transit protection material.

Tools required:

•  Philips head screwdriver (or cordless drill  

and bits).

•  Flat head screwdriver.
•  Adjustable spanner.

STEP 1
Inside of the LPG compartment the gas hose and 
regulator assembly are already connected to the 
gas inlet of the appliance.
Place LPG cylinder in the LPG compartment.
Make sure the LPG cylinder base sits inside the 
metal stand easily and completely.
Turn the wing screw on the outer part of the metal 
stand clockwise to secure the LPG cylinder tightly.

STEP 2
Ensure cylinder valve is in its full off position. 
Check for any damage to either the cylinder 
connection or the hose. NEVER attempt to use 
damaged equipment. Attach the regulator and 
hose to your gas cylinder. Tighten the nut to a 
positive stop by hand.

STEP 3
Turn on the gas cylinder ensuring that the control 
knob on the outdoor heater is turned OFF at this 
point. DO NOT ATTEMPT TO LIGHT THE HEATER.

STEP 4
Use a solution of soapy water (dishwashing liquid 
and water is fine). Brush it on or use a spray bottle 
as shown in the drawing. Ensure the connections 
have a good coating.

STEP 5a
If the connection is leaking, bubbles will start to 
grow in the soapy solution. If this happens shut off 
the gas supply at the cylinder.

STEP 11

Ensure cylinder valve is in its full off position. Check 
for any damage to either the cylinder connection or 
the hose. NEVER attempt to use damaged equipment. 
Attach the regulator and hose to your gas cylinder. 
Tighten the nut to a positive stop by hand.

STEP 12

Turn on the gas cylinder ensuring that the control knob 
on the outdoor heater is turned OFF at this point.
DO NOT ATTEMPT TO LIGHT THE HEATER!!.

STEP 13

Use a solution of soapy water (dishwashing liquid and 
water is fine). Brush it on or use a spray bottle as 
shown in the drawing. Ensure the connections have a 
good coating.

STEP 14a

If the connection is leaking, bubbles will start to grow 
in the soapy solution. If this happens shut off the gas 
supply at the cylinder. 

STEP 14b

Tighten the connections using a crescent then repeat 
steps 12-13.  

STEP 14c

The connection is gas tight when no bubbles grow 
around the gas connection.

ASSEMBLY INSTRUCTIONS

STEP 11

Ensure cylinder valve is in its full off position. Check 
for any damage to either the cylinder connection or 
the hose. NEVER attempt to use damaged equipment. 
Attach the regulator and hose to your gas cylinder. 
Tighten the nut to a positive stop by hand.

STEP 12

Turn on the gas cylinder ensuring that the control knob 
on the outdoor heater is turned OFF at this point.
DO NOT ATTEMPT TO LIGHT THE HEATER!!.

STEP 13

Use a solution of soapy water (dishwashing liquid and 
water is fine). Brush it on or use a spray bottle as 
shown in the drawing. Ensure the connections have a 
good coating.

STEP 14a

If the connection is leaking, bubbles will start to grow 
in the soapy solution. If this happens shut off the gas 
supply at the cylinder. 

STEP 14b

Tighten the connections using a crescent then repeat 
steps 12-13.  

STEP 14c

The connection is gas tight when no bubbles grow 
around the gas connection.

ASSEMBLY INSTRUCTIONS

STEP 11

Ensure cylinder valve is in its full off position. Check 
for any damage to either the cylinder connection or 
the hose. NEVER attempt to use damaged equipment. 
Attach the regulator and hose to your gas cylinder. 
Tighten the nut to a positive stop by hand.

STEP 12

Turn on the gas cylinder ensuring that the control knob 
on the outdoor heater is turned OFF at this point.
DO NOT ATTEMPT TO LIGHT THE HEATER!!.

STEP 13

Use a solution of soapy water (dishwashing liquid and 
water is fine). Brush it on or use a spray bottle as 
shown in the drawing. Ensure the connections have a 
good coating.

STEP 14a

If the connection is leaking, bubbles will start to grow 
in the soapy solution. If this happens shut off the gas 
supply at the cylinder. 

STEP 14b

Tighten the connections using a crescent then repeat 
steps 12-13.  

STEP 14c

The connection is gas tight when no bubbles grow 
around the gas connection.

ASSEMBLY INSTRUCTIONS

STEP 11

Ensure cylinder valve is in its full off position. Check 
for any damage to either the cylinder connection or 
the hose. NEVER attempt to use damaged equipment. 
Attach the regulator and hose to your gas cylinder. 
Tighten the nut to a positive stop by hand.

STEP 12

Turn on the gas cylinder ensuring that the control knob 
on the outdoor heater is turned OFF at this point.
DO NOT ATTEMPT TO LIGHT THE HEATER!!.

STEP 13

Use a solution of soapy water (dishwashing liquid and 
water is fine). Brush it on or use a spray bottle as 
shown in the drawing. Ensure the connections have a 
good coating.

STEP 14a

If the connection is leaking, bubbles will start to grow 
in the soapy solution. If this happens shut off the gas 
supply at the cylinder. 

STEP 14b

Tighten the connections using a crescent then repeat 
steps 12-13.  

STEP 14c

The connection is gas tight when no bubbles grow 
around the gas connection.

ASSEMBLY INSTRUCTIONS

Содержание Keystone GM142-140













Отзывы: