Gasboy Islander ICR PLUS Скачать руководство пользователя страница 5

Страница: 5 / 146

TABLE OF CONTENTS

Paragraph

Page

GENERAL DESCRIPTION

SECTION 1

1-1.

SCOPE ................................................................................................................................ 1

1-2.

DESCRIPTION .................................................................................................................. 1

1-3.

SYSTEM OVERVIEW ...................................................................................................... 3

1-3.1.

Islander PLUS System ................................................................................................... 3

1-3.2.

Vehicle Identification – FuelPoint PLUS ...................................................................... 3

1-3.3.

Remote Web Access ...................................................................................................... 3

1-3.4.

Head Office .................................................................................................................... 3

1-3.5.

Restrictions and Limits .................................................................................................. 3

1-3.6.

Islander PLUS Capabilities for Forecourt Management ................................................ 4

1-3.7.

System Workflow Example ........................................................................................... 4

1-3.7.1.

Refueling Scenario with FuelPoint PLUS ................................................................. 5

1-3.7.2.

Refueling Scenario with Magnetic Cards .................................................................. 5

1-4.

ISLANDER PLUS STRUCTURE ..................................................................................... 6

1-4.1.

Main Components .......................................................................................................... 6

1-4.2.

Islander PLUS Internal Configuration – Mechanical Pump .......................................... 9

1-4.3.

Islander PLUS Main Components Location ................................................................... 11

1-5.

AVAILABLE CONFIGURATIONS ................................................................................. 16

1-5.1.

General ........................................................................................................................... 16

1-5.2.

Islander PLUS / ICR PLUS ........................................................................................... 16

1-5.3.

Printer Option ................................................................................................................. 16

1-5.4.

Vehicle Identification System ........................................................................................ 16

1-5.5.

Dispensers ...................................................................................................................... 16

1-5.6.

Contactless Tags/Cards .................................................................................................. 17

1-5.6.1.

Data Key Sockets – Fleet key ................................................................................... 17

1-5.6.2.

HID Device ............................................................................................................... 17

1-5.6.3.

Configurations ........................................................................................................... 17

1-6.

SECURITY AND PROTECTION ..................................................................................... 20

1-6.1.

General ........................................................................................................................... 20

1-6.2.

Authorization Security ................................................................................................... 20

1-6.3.

Network Security ........................................................................................................... 20

1-6.4.

RF Network Security ..................................................................................................... 20

1-6.5.

Maintenance Security ..................................................................................................... 20

1-7.

HOUSING .......................................................................................................................... 20

Islander PLUS Manual

Содержание Islander ICR PLUS



















































































































































Результаты поиска

Содержание Islander ICR PLUS

Отзывы:

Бренды по названию

Популярные бренды

Gasboy Islander ICR PLUS, Руководство по установке

Результаты поиска

Содержание Islander ICR PLUS

Отзывы:

Бренды по названию

Популярные бренды