GAS GAS F0103TG Скачать руководство пользователя страница 60

Страница: 60 / 121

11 SERVICE WORK ON THE CHASSIS

11.36

Adjusting the free travel of the clutch lever

E01363-13

–

Check the free travel of the clutch lever. (

p. 57)

–

Loosen nut

–

Adjust the free travel of the clutch lever with adjusting screw

Info

Turn the adjusting screw clockwise to reduce free travel. The
pressure point moves away from the handlebar.

Turn the adjusting screw counterclockwise to increase free
travel. The pressure point moves towards the handlebar.

The range of adjustment is limited.

Do not use force.

Do not make any adjustments while riding.

–

Hold adjusting screw

and tighten nut

11.37

Adjusting the basic position of the clutch lever

E01363-11

Main work

–

Adjust the basic position of the clutch lever to your hand size by
turning adjusting screw

Info

Turn the adjusting screw counterclockwise to decrease the
distance between the clutch lever and the handlebar.

Turn the adjusting screw clockwise to increase the distance
between the clutch lever and the handlebar.

The range of adjustment is limited.

Do not use force.

Do not make any adjustments while riding.

Finishing work

–

Check the free travel of the clutch lever. (

p. 57)

11.38

Checking/correcting the fluid level of hydraulic clutch

Note

Environmental hazard

Hazardous substances cause environmental damage.

–

Dispose of oils, grease, filters, fuel, cleaning agents, brake fluid, etc., correctly and in compliance with the appli-
cable regulations.

Info

The fluid level rises with increasing wear of the clutch facing discs.

Do not use brake fluid.

Содержание F0103TG


























































































































Результаты поиска

Содержание F0103TG

Отзывы:

Похожие инструкции для F0103TG

Бренды по названию

Популярные бренды

GAS GAS F0103TG, Руководство пользователя

Результаты поиска

Содержание F0103TG

Отзывы:

Похожие инструкции для F0103TG

Бренды по названию

Популярные бренды