background image

1-2

GENERAL INFORMATION

WARNING/CAUTION/NOTE

Please read this manual and follow its instructions carefully. To emphasize special information, the symbol
and the words WARNING, CAUTION and NOTE have special meanings. Pay special attention to the mes-
sages highlighted by these signal words.

Indicates a potential hazard that could result in death or injury.

Indicates a potential hazard that could result in motorcycle damage.

NOTE:
Indicates special information to make maintenance easier or instructions clearer.

Please note, however, that the warnings and cautions contained in this manual cannot possibly cover all
potential hazards relating to the servicing, or lack of servicing, of the motorcycle. In addition to the WARN-
INGS and CAUTIONS stated, you must use good judgement and basic mechanical safety principles. If you
are unsure about how to perform a particular service operation, ask a more experienced mechanic for
advice.

GENERAL PRECAUTIONS

Proper service and repair procedures are important for the safety of the service mechanic
and the safety and reliability of the motorcycle.
When two or more persons work together, pay attention to the safety of each other.
When it is necessary to run the engine indoors, make sure that exhaust gas is forced out-
doors.
When working with toxic or flammable materials, make sure that the area you work in is well
ventilated and that you follow all of the manufacturer’s instructions.
Never use gasoline as a cleaning solvent.
To avoid getting burned, do not touch the engine, engine oil, radiator, and exhaust system
until they have cooled.
After servicing the fuel, oil, engine coolant, exhaust or brake systems, check all of the lines,
and fittings related to the system for leaks.

Содержание DR-Z400SY










Отзывы: