GarrettCom Magnum QS5108 Скачать руководство пользователя страница 38

Страница: 38 / 55

Magnum Quad-Series Fiber Switches

Installation and User Guide (06/03)

converters mostly do not support auto-negotiation properly, and require that the switched

port to which they are connected be at 100Mb fixed speed. Attachment to 10/100 auto-

negotiation ports typically will not work properly. The Quad-Switch’s RJ-45 ports

ection 3.4)

0Mb

lly

highest order mode that both devices can support at that time. (Since auto-

negotiati

When operating in 100Mb half-duplex mode, cable distances and hop-counts

t collision domain. The Path Delay Value (PDV) bit-times must

account f

Fast Ethernet switched ports operating at 100Mb half-duplex, the bit time delay is 50BT.

handle this situation by changing the internal jumper settings. (see S

When Quad-Switch’s RJ-45 copper ports are set for auto-negotiation and

connected to an another auto-negotiating device, there are 4 different speed and F/H

modes selection depending on what the other device supports. These are: (1) 10

full-duplex, (2) 100Mb half-duplex, (3) 10 Mb full-duplex and (4) 10 Mb half-duplex.

The auto-negotiation logic will attempt to operate in descending order and will norma

arrive at the

on is potentially an externally-controlled process, the original “highest order

mode” result can change at any time depending on network changes that may occur). I

the device at the other end is not an auto-negotiating device, the Quad-Switch’s RJ-45

ports will try to detect its idle signal to determine 10 or 100 speed, and will default to

half-duplex at that speed per the IEEE standard.

General information -

Auto-negotiation per-port for 802.3u-compliant switches occurs when:

the devices at both ends of the cable are capable of operation at either 10

Mb or 100Mb speed and/or in full- or half-duplex mode, and can

send/receive auto-negotiation pulses, and . . .

-- when the second of the two connected devices is powered up*, i.e.,

when LINK is established for a port, or

-- when LINK is re-established on a port after being lost temporarily.

•

NOTE

–

some NIC cards only auto-negotiate when the computer system

that they are in is powered up. These are exceptions to the “negotiate at

LINK – enabled” rule above, but may be occasionally encountered.

may be limited within tha

or all devices and cable lengths within that domain. For Magnum Quad-Serie

www GarrettCom com

Содержание Magnum QS5108
























































Результаты поиска

Содержание Magnum QS5108

Отзывы:

Похожие инструкции для Magnum QS5108

Бренды по названию

Популярные бренды

GarrettCom Magnum QS5108, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Magnum QS5108

Отзывы:

Похожие инструкции для Magnum QS5108

Бренды по названию

Популярные бренды